Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Spray can Nozzel

Posts

Spray can Nozzel

#1

Spray can Nozzel

CGelnett

>Since I am only finishing one bowl or turned box at a time I normally use a spray can. Less clean up and ready to go right off the shelf, but I keep having problems lately with the nozzle plugging up. I normally turn the can upside down for a few seconds and even wipe off any drips on the front of the nozzle. This has worked for me the past several years but lately the nozzle still gets partially plugged. The nozzle is plugged just enough that when I start to spray my project I get a stream of finish.

I have tried taking the nozzle off and soaking it but that does not work very well.

Any ideas?

Re: Spray can Nozzel

#2

Re: Spray can Nozzel

John K Jordan

>>I normally turn the can upside down for a few seconds

Forgive the obvious, but be sure you spray upside down long enough that the liquid spray stops and the nozzle is just passing gas. (my, but that sounds odd) This doesn't work with some cans I have that spray in any position!

You can also remove the nozzle before storage and blow compressed air through it. I've had good luck with cleaning nozzles by soaking in solvent then reaming with a very fine wire. I've also replaced problem nozzles with those pulled out of empty paint cans.

JKJ

Re: Spray can Nozzel

#3

Re: Spray can Nozzel

CGelnett

>Thanks John, maybe I am not waiting long enough when spaying upside down.

I have not had much luck at cleaning the nozzles when soaking them. What are you soaking them in?

Re: Spray can Nozzel

#4

Re: Spray can Nozzel

John Lucas

>I will occasionally put the nozzles in a baby food jar with some mineral spirits and let them sit. I have that problem with my spray adhesive and people at work never turn them upside down so the nozzles are always clogged. It usually works but not every time.

With polyurethanes it probably won't work.

Re: Spray can Nozzel

#5

Re: Spray can Nozzel

Mike Daddis

>Wouldn't it be nice if there was a source where you could buy a bag full of replacement nozzles? They can't cost all that much.

Anyone heard of a source like this?

Re: Spray can Nozzel

#6

Re: Spray can Nozzel

CGelnett

>That would be nice. Last year I sent email to Minwax and asked them if they sold the nozzle separately and the answer was no. I tried talking them into it but the answer was still no.

Be nice if they would sell to our club in mass.

Re: Spray can Nozzel

#7

Possible Source

Al Goldstein

>If I remember correctly, I once bought some replacement nozzles for spray cans from American Science & Surplus (www.sciplus.com). I just checked and they don't have any in stock. This company is a good source for all sorts of stuff, some useful and others not - some quite inexpensive and others not.

I still have some packets of replacement nozzles in my shop. The company is Workshop Timesavers Inc. P.O. Box 68037 Rochester NY 14618

Write them a letter and see if they still sell them. Good luck.

Re: Spray can Nozzel

#8

Re: Spray can Nozzel

Gary Evans--Tallassee TN

>The best place to get a very small diameter, very stiff wire is to pull one out of a steel brush. I do this all the time for cleaning motorcycle carburetor jets.

Gary

Re: Spray can Nozzel

#9

Re: Spray can Nozzel

John K Jordan

>>What are you soaking them in?

Depends on what was in the can, usually generic paint thinner.

JKJ

Re: Spray can Nozzel

#11

Rob Wallace

Re: Spray can Nozzel

Rob Wallace

>Chet:

Mineral spirits won't touch built-up lacquer deposits - you must use lacquer thinner. I also have tried the "thin-wire ream-out" technique and it works about half the time, although the atomization seems to never be as good as the 'original' spray.

Once polymerized, polyurethane will be difficult to dissolve with any thinner; you could try lacquer thinner or even acetone....some solvents might damage the nozzle's plastic, however...

I also do what John does, and "borrow" working nozzles from other cans. I use a lot of Deft spray lacquer cans, and whenever one is finished, I save the nozzle for future use before I discard the empty can (I now have a small jar full of extra nozzles!).

I have found that some brands of spray lacquer clog the nozzles more than others - i.e. both Behlen spray lacquers [pre-cat and nitrocellulose] tend to clog the nozzles easily, despite careful inversion spraying and blow-out cleaning - I don't use them any more. Watco spray lacquer is a bit better for not clogging, but I don't like the finishing characteristics of the lacquer (tends to blush easily). I've been happy with Deft lacquer, and use it almost exclusively when I do a spray finish.

I hope this helps a bit...

Rob Wallace

Re: Spray can Nozzel

#12

Re: Possible Source

Carol Reed - Strawberry, AZ

>Geez! Who knew there were so many different types of caps? I'm gonna start saving mine!

Re: Spray can Nozzel

#13

Re: Spray can Nozzel

John Lucas

>I also keep a bottle of lacquer thinner there also. I put my clogged CA glue tips in there as well as the lacquer spray paint tips.

Re: Spray can Nozzel

#14

Re: Spray can Nozzel

bob davis5098

>i use deft exclusively. no problrm with clogged nozzles..i do save the old ones in case of a rare problem

Re: Spray can Nozzel

#15

Re: great site, thanks

Matt Overton

>

Re: Spray can Nozzel

#16

Re: Spray can Nozzel

Barry Turner

>I do what you do, turn the can upside down and spray to clear the nozzle. Works for me. If you have to resort to soaking a clogged nozzle, make sure the solvent is appropriate to what is in the spray can. Lacquer thinner for lacquers and mineral spirits for polyurethanes.