Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

How I spent Jan 1,2010

Posts

How I spent Jan 1,2010

#1

Steven Antonucci

How I spent Jan 1,2010

steve antonucci

>I took this piece of maple to the lathe at probably close to 60 pounds and now it's less than 2 pounds. About 6 hour, which 4 were with the lathe spinning, and 2 were futzing around since I had the house to myself today.

The ambrosia in this log is pretty darn nice, if I do say so myself! I was aiming for a lampshade, but I stopped at a bowl instead. It is very hard to measure the bottoms of these, since light passes more easily through engrain than side grain. It looked for anything like it was 1/8", but is probably 5/16" or better at the bottom 1/3. I need to make a toolrest for this type of work to get deeper in without vibration.

Wife commented that it smelled like manure, so clean up tomorrow... maybe.

S


img

Re: How I spent Jan 1,2010

#2

Re: How I spent Jan 1,2010

Carole Valentine

>Steve, how much weight do you have on your lathe? Was that blank pretty balanced when you mounted it? Looks like a good day making shavings.

Re: How I spent Jan 1,2010

#3

Re: How I spent Jan 1,2010

Texian

>Great start to the new year. Pls. show us when finished.

Re: How I spent Jan 1,2010

#4

Steven Antonucci

Start slowly

steve antonucci

>I have had my Nova for many years, and I've found that it is pretty stable if I start at about 400rpm or lower. The third pulley step is the one where I start to pick up vibration.

Since this was turned endgrain, it was fairly balanced at the start. I did remove a bunch of wood at the foot end with a chainsaw, but only because I couldn't get it to clear the ways. Probably should have taken more off this way, since it would have saved a bit on the clean-up!

As far as weight on the lathe goes, the Nova cast iron legs are something like 75# each. They have the knock outs to fit 2x6, and I build that small box you see by encasing the top and bottom. It is filled with gravel from my driveway, and I would guess it's another 100#. The boat battery is probably 40#, and the water softener salt bag adds another 20# or so. When we had a water softener, I would stack the bags on the shelf as balast (and I had to put them somewhere).

The lathe is rock solid if you keep the speed down until balanced. Once it is balanced, you can usually do whatever you want at any speed, but then I have to sweep up wood all the way to the back of the shop, as it tends to fly quite a bit further with RPMs.

If I wanted to, I could make the box go to the floor. I left it open so I could sweep, but if it went to the floor, I wouldn't need to sweep under it, right?

Steve

Re: How I spent Jan 1,2010

#5

Steven Antonucci

Looking down from the top

steve antonucci

>I have about 40' of this log (if I want to go pick it up). Going to smell bad for a long time...


img

Re: How I spent Jan 1,2010

#6

Re: How I spent Jan 1,2010

john lucas

>Glad you had fun. I think I've had my fill of large bowls. I can't sell them, they make a humongous mess, take many times as long as smaller bowls to sand, and they take longer to finish and buff. If I could get the $10 per inch fee that some are charging I suppose it might be worth it but I end up giving them away to charity events.

Buy cutting the same size log up into smaller bowl blanks I get more bang for my buck around here. I may have to start doing shows again this year depending on how my job goes. I will definitely put some large bowls in the booth to see the response. If nothing else they might lead to some commission pieces.

It does give you a great feeling when you finish one though and I guess that's why we do it. Yours looks great. Your gonna have fun with this wood smell or not.

Re: How I spent Jan 1,2010

#7

Don Pencil

Re: How I spent Jan 1,2010

Don Pencil

>Great bowl!

As for the lampshade...you make those before Dec. 31. Then you will have something to wear that night as you dance on the table celebrating the incoming year.

Good Work.

Be Well,

Don

Re: How I spent Jan 1,2010

#8

Brad Vietje

Re: Looking down from the top

Brad Vietje

>Nice work, Steve,

What are you using for removing wood?

I've only done a few lampshades, and have used a Martel Hook Tool for most of the work, and a Sorby Hooker Tool on an Armbrace handle with a teardrop scraper for thinning the walls. Pretty delicate work. I've never tried to retain the bark, which must make it even harder!

I like the occasional large piece, and even if they are harder to sell, as John replied. They are more eye-catching, and can attract people to a sales booth. Otherwise, they make bigger gifts with a lot more WOW factor, even if the bulk of the work is smaller and less expensive.

Glad your New Year is off to such a messy & fun start!

Brad Vietje

Newbury, VT

Re: How I spent Jan 1,2010

#9

Steven Antonucci

I make my own hooks

steve antonucci

>I have been hammering out hooks since I watched Adnre cut with one 3 years ago at Totally Turning. They cut very fast and very clean. I can make on in about 10 minutes, and usually make a few in batches.

I cut them off of the rod and put them in my boring bars. I have a 3/4"bar that I like that far over the rest. Pretty nice having that much mass 12" over the edge of the rest. I also used a teardrop scraper in shear to unify the surface. The bark is not at all hard to keep on, just cut that area once with sharp tools and never go back.

I may take one more shot at it tomorrow, as I spent a few minutes this AM working on the big bar (added another set screw and a shim). I finished the outside with a cabinet scraper and the lathe running very slowly (works great, but not for the novice). I'll hand scrape any remaining marks out in a few days after the wood has settled a bit- just to avoid spending a lot of time on a vessle that may split!

Big work is a very big problem- I've noticed that folks are always drawn to size, even if they don't but it. If I was looking to sell, I'd want to have the larger pieces just to draw the crowds, even if I packed them home every night.

Sore as heck today...

s

Re: How I spent Jan 1,2010

#10

Tool rest for deep bowls

Jorge Castaneda~Downeast Maine

>Steve,

Here is a tool rest I made myself in an adult ed class at the local HS.

It extends roughly 9 inches from the post and the short arm measures 2 1/4", The post is 1" x 6", and the rest proper is only 7/8" because I am a wimp and could not bend the 1" bar but managed to bend the 7/8". Mistake, in most woods is fine but in certain woods vibrates some. The extra 1/8" would add quite a bit more mass and rigidity and that should be better. second thing to improve, is been not long enough several times, so next one will have 1 1/2" or 2" more reach. Also some times as I make bowls that are wider at the equator than at the arctic circle, so I want to make a rest that is bent past 90 degrees, perhaps all the way to 60, so it can reach better in that wide spot, I did get a D.T. 3/4" bowl gauge for this reason, quite a whooper, it is a long overhang, and the gouge does the job, but it generates a lot of friction, so the proper tool rest hopefully will let me use the 1/2" gouge that is my workhorse.

Total cost around $7.00 in materials 3 years ago.

Hope the shop teacher offers shop time this adult ed season that stars in a couple weeks.

Unlike other fellows, it seems that I never manage to make big bowls and platters fast enough, there is always people that walk away empty handed and I always have several at least 14", the bigger ones sell faster.

Jorge


img

Re: How I spent Jan 1,2010

#11

Re: How I spent Jan 1,2010

Eric Knutsen

>Bring it to the next NJWT meeting.....

Re: How I spent Jan 1,2010

#12

Steven Antonucci

I was supposed to be demoing, but I'm at Disney

steve antonucci

>It will have to wait until February, Eric. I have a family vacation that overlaps the next meeting.

I will bring it (or something very similar) to the Feb Meeting.

S

Re: How I spent Jan 1,2010

#13

Steven Antonucci

Did you fit the two bars together?

steve antonucci

>Did you do any file work to fit them together before the weld? Or was it just a quick weld? I don't care what it looks like if it works!)

S

Re: How I spent Jan 1,2010

#14

Re: Did you fit the two bars together?

Jorge Castaneda~Downeast Maine

>Hi Steve,

No fitting, just build up with the arc welder, a little on either side until it was even all around. and a Little grinding afterward.