Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Coloring Question - Jamie D. & others

Posts

Coloring Question - Jamie D. & others

#1

Coloring Question - Jamie D. & others

jake Niedling

>Jamie,

I know that you took a class this year on coloring your pieces and I have seen some of your pieces here on Wood Central. I have a curly maple hollow form ( 3" dia x 2" tall not including the finial) that I want to color to highlight the grain pattern that shows well around the large diameter. Not much of the curly pattern shows around the top or bottom side. My experience with coloring always ends up with the wood not taking the coloring evenly due to the side grain and end grain. So what is the trick to get a nice even color all around the turning? Do you put a sanding sealer on first? Appreciate your help and insight and anyone else that has experience or tips.

Thanks,

Jake

Re: Coloring Question - Jamie D. & others

#2

Re: Coloring Question - Jamie D. & others

Texian

>Recently read a post about using sealer on only the end grain areas to even out the color. Seems like it would be difficult to know exactly how much area to seal.

Re: Coloring Question - Jamie D. & others

#3

Ask Jim Shaver

Jorge Castaneda~Downeast Maine

>Jake,

sometime this year I think, Jim Shaver had a post explaining how he did a knock out grain popping on a piece. do a search or question him directly. It involves alcohol dyes at mild solutions, so you can build up until you get what you want. and two different dyes IIRC.

Jorge

Re: Coloring Question - Jamie D. & others

#4

Re: You cannot apply any sealer if.....

JamieD

>...if dye is to be applied to the wood. The wood has to be very well sanded to at least 400 grit, then dye will accentuate the grain variations. You then sand back the surface to remove some of the surface dye, leaving the darker dye in the softer parts of the figure which absorbed more dye. Don't initially apply a thick dye coat, but darken gradually with several coats as desired. Good permanent dye like TransTints can be mixed with either alcohol or water, and for a small object like yours I would use alcohol to reduce grain raising and drying time. This process requires experimentation to predict results, and practice on a sanded board of wood similar to the project wood will give you good feedback about how to perfect the process before applying to a turning. And don't forget the rubber gloves!

Re: Coloring Question - Jamie D. & others

#5

no sealer

john lucas

>If you seal it you even out the differences between the figure and the non figure areas. You want the opposite. Jamie stated it well. I find that when you sand it back you have to take it really slow. It's way to easy to remove too much color from the areas where the grain does not penetrate.

To leave it natural looking add just a hint of a brown color. let that penetrate the figure areas. Then sand the non figured areas back to natural wood and proceed with your favorite finish.

Re: Coloring Question - Jamie D. & others

#6

Re: You cannot apply any sealer if.....

jake Niedling

>A couple of questions:

1. spray or wipe the dye on? If you wipe, what to you use?

2. What grade of sanding paper do you use to sand back with?

3. If you put on just one color, how many times to you usally apply it? Do you apply several coats of a thinned down color to get the final color rather than one single dark coat? Sort of build up to the final color?

Thanks,

Jake

Re: Coloring Question - Jamie D. & others

#7

Re: You cannot apply any sealer if.....

john lucas

>Jake I wiped it on using water based analine dye. I have used 600 grit or 4/0 steel wool to take it back. I usually mix the dye up thin and try it on scrap until I get roughly the color I want. I would rather apply a few layers and build it up instead of one thick one and get it wrong. If I did a lot of that I could probably nail it with one coat but you know me, I hardly ever wood of that quality. I'm usually using opaque paints to cover up crappy wood.

Re: Coloring Question - Jamie D. & others

#8

Re: John covered several of your ..........

JamieD

>....questions, but I sand back with 320 and am trying to make people aware of the advantages of using more permanent dyes like TransTints. I apply many dye/finishing materials with squares of yellow foam carpet padding, cheap and readily available.

Re: Coloring Question - Jamie D. & others

#9

Here you go... *LINK*

Jorge Castaneda~Downeast Maine

>Jake,

found it

Jorge


Popping the Curl

Re: Coloring Question - Jamie D. & others

#10

Thanks for the advice.......

jake Niedling

>