Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

another use for Beal buffer

Posts

another use for Beal buffer

#1

another use for Beal buffer

John K Jordan

>I don't know if anyone has posted about this before, but the Beal buffing wheels are great for repairing scratched CDs and DVDs. I used to repair by hand with polishing compound but this is a lot quicker.

I use both the tripoli and white diamond wheels and clean as needed with DNA on a soft cloth. So far, this has worked every time, even on some disks with some horribly deep scratches. If the scratches are severe, I sand up to the finest grit I have before buffing. (Note that most of the thickness of a disk is in the clear plastic on the data access side so you can remove quite deep scratches. The label side, otoh, is relatively fragile.)

I rotate the disk around the point of contact with the wheel while buffing my way around the disk so each area gets overlapping and crossing abrasion. This takes about 10 minutes or so, depending on the level of damage. Don't fret about the cloud of very tiny scratches left by the white diamond compound - the laser can "see" right through them. (The plastic surface is a long relative distance from the metal data layer and considerably "out of focus" to the laser optics.)

I've heard there are polishing machines in some video stores but this has to be more fun. It is best done wearing a WoodCentral shirt.

Be careful to hold the disk tightly - I suspect slinging it across the room wouldn't help the data.

JKJ


img

Re: another use for Beal buffer

#2

Re: another use for Beal buffer

Nick Tuzzolino

>What is "DNA" that you use on a soft cloth?

Re: another use for Beal buffer

#3

denatured alcohol

Matt Overton

>

Re: another use for Beal buffer

#4

Re: another use for Beal buffer

Jeff Brockett

>Nice.

Re: another use for Beal buffer

#5

Don Pencil

"PL"

Don Pencil

>John,

It works great. I've done that myself.

PS

That is one of the uses the "PL" realy works great on and fast. It will give you a better finish also. For even a better finish after that you can lightly buff them out with carnauba wax if you like.

Be sure to buff out the wax with a cotton cloth afterward to get ride of any minor but left over wax.

Be Well,

Don

Re: another use for Beal buffer

#6

"PL" - what is it?

John K Jordan

>>That is one of the uses the "PL" realy works great on

>and fast. It will give you a better finish also.

I'm not familiar with the "PL". Is it a buffing system like the Beall? If so, what kind of wheels and compounds does it use and where can I find it?

I've been looking for something better for polishing plastic. Years ago I refurbished one of our aircraft windshields with a Micro-Mesh kit. (If I remember, these abrasives were used for aircraft long before pens.) The windshield looked like new when I was done but took hours of work by hand.

JKJ

Re: another use for Beal buffer

#7

Rob Wallace

Re: "PL" - what is it? *LINK*

Rob Wallace

>John:

"PL" is an abrasive compound used for buffing-out 'P'lastic and 'L'acquer finishes with a buffing wheel (BTW - "plastic finishes", include polyurethanes and acrylics). Don Pencil has recently been selling a kit that includes a stick of this compound and an 8" buffing wheel. I just purchased one of these kits in Albuquerque this summer at the AAW Symposium, and have only limited experience using it (hard to get out of my standard Beall buffing process); the PL compound does a pretty good job of putting a gloss finish on the lacquer finishes I have used it on, using only one buffing step.

Hopes this helps. See the link below.

Rob Wallace


PL Buffing Compound and Instructions