Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

segmented bowl bloodwood bleeds

Posts

segmented bowl bloodwood bleeds

#1

segmented bowl bloodwood bleeds

Ed Jones

>Feature ring on segmented bowl is fishook design with bloodwood and maple. Problem is the bloodwood "bleeds" red just like a blood smear on to the maple. There are over 200 pieces of maple and bloodwood in this ring, with the ring 1.5" high. Several attemps to finish -all with blood smears on the maple.

1st try- sanded thru grits to 400- raged on shellac base finish -smears. Thought fine sawdust was the problem- removed finish.

2ND TRY- scrapper used only- no sanding- applied finish same problem. Must be finish that reacts to bloodwood- removed finish.

3rd try- sanded to 400 after removing finish. raged on lacquer dealer- same problem

4th try scraped off finish. With lathe at very slow speed sprayed on mist coats of deft. Much better just slight bleed . The finish must be disolving something from the bloodwood

Anyone have or solved this problem. Thanks for reading this.

Re: segmented bowl bloodwood bleeds

#2

Re: segmented bowl bloodwood bleeds

russ faifield

>Bloodwood bleeds and Padauk is worse. We have to remember that dyes can be extracted from these species with the same thinners that are used for lacquer and shellac.

I have done fairly well with high pressure air to clean all of the sanding dust out of the the wood, followed by a wash of Odorless Mineral Spirits, and then more air until it is dry and clean. Then I spray the area with Krylon Workable Fixitif (available at art supply stores). After that the wood is pretty much sealed for any finish you want to put on it, but I would still spray the lacquer if that is your choice of finish. I use an oil finish that is padded on and just plan on using more coats to get the same gloss.

I know there are other ways to solve this problem, and it will be interesting to see the responses you get.

Re: segmented bowl bloodwood bleeds

#3

Re:Russ- I know many turners use this .....

JamieD

>...Krylon Fixitif, but what is it exactly? I can guess it may be a thin satin or semigloss lacquer, but what other material would be similar in use and available in a rattle can??

Re: segmented bowl bloodwood bleeds

#4

Re:Russ- I know many turners use this .....

John Lucas

>Jamie Krylon Fixatif is available in a rattle can. I actually don't know of an other way to buy it. I don't know what it is but it was designed to spray on pastel prints to keep them from wiping off. I changes the wood color less than anything I've tried although it will still change the color in some woods just like water will.

Re: segmented bowl bloodwood bleeds

#5

Re: segmented bowl bloodwood bleeds

John Lucas

>Ed I haven't done bloodwood but have done a maple and Paduak piece. I had good luck by applying lacquer sanding sealer before sanding. Then sanding, blowing and or wiping away all dust. Apply more sealer and sand with the next grit. Keep doing that until I feel I've built up enough finish so that it doesn't carry any sanding dust over.

I spray on the finish and that might be one advantage. When you brush on or wipe on a finish the padauk bleeds like crazy.

Re: segmented bowl bloodwood bleeds

#6

Re:John- I used it years ago to fix.......

JamieD

>..pencil and charcoal drawings, but haven't checked a label lately to see exactly what the material is made of?

Re: segmented bowl bloodwood bleeds

#7

Re:Russ- I know many turners use this .....

russ faifield

>The can doesn't say what it is and their MSDS sheet only lists the volatiles, but my nose tells me it is a Melamine lacquer.

The only other commercial melamine lacquer that I know of is made by Mylands, and I don't know if that is still available in the US.

Re: segmented bowl bloodwood bleeds

#8

Russ- what type lacquer is Deft?

JamieD

>

Re: segmented bowl bloodwood bleeds

#9

Re: Russ- what type lacquer is Deft?

russ faifield

>Deft is a common nitro-cellulose lacquer.

Re: segmented bowl bloodwood bleeds

#10

deft

bob davis5098

>

Re: segmented bowl bloodwood bleeds

#11

Re: segmented bowl bloodwood bleeds

GalenV in Iowa

>Ed

I ask the same question when I did some simple bloodwood and maple boxes. I think it was John's method I used. Spray Deft lacquer sanding sealer before I sanded. Piece was not turning while coating other than to roll over by hand. Very light sand then another spray coat of sealer and down through grits. Used air to blow off each time as touching it with any liquid or tack cloth would make it bleed or even the dust get in the maple grain.

I have seen large segmented turnings such as you are making and there was no bleeding. Think there are a few that have hidden formula to finish. But then I'm a beginner.

Galen

Re: segmented bowl bloodwood bleeds

#12

Re: Russ- another Krylon product that....

JamieD

>.. I've been using lately is Triple Thick Crystal Glaze, and again there is no info on the can to define what the material is inside- can you identify?