Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Making a pen without a pen mill?

Posts

Making a pen without a pen mill?

#1

Making a pen without a pen mill?

wilbur

>I'm trying to make some pens tonight, and all the various methods I've seen call for using a pen mill to square up the shoulders of the pen blanks after drilling and gluing in the brass barrel. Which is fine, except that my pen mill doesn't seem to be working all that well tonight.

I am going to try to tune up the pen mill, but I was wondering if there was a way of making a pen without using a pen mill for this step. I was always told that just sanding the ends of the blank could lead to ends that are not perfectly square. I suspect that there must be a way to not use a pen mill based on a conversation I had with the Berea Hardwoods folks a while ago as to why they didn't carry pen mills. They said they didn't carry pen mills because they didn't recommend them, but then I forgot to ask what they would recommend instead.

Thanks!

Re: Making a pen without a pen mill?

#2

Re: Making a pen without a pen mill?

Charles Yawn

>Get the wood parts square with the brass tube and you are set to seat the bushings. Charles

Re: Making a pen without a pen mill?

#3

Katherine Kowalski

Re: Making a pen without a pen mill?

Katherine Kowalski

>You can easily square up the end of the tube with the wood by using the mitre gauge on the disc sander -- just sand until you can see the "shine" of the metal.

(I don't use pen mills either...)

Re: Making a pen without a pen mill?

#4

Re: Making a pen without a pen mill?

Marc Phillips

>I use a disc sander... and a miter gauge...

But...

You need to "square" up the blank... yes, but you need to square it up using the brass tube as the reference, not the side of the wood blank against a miter gauge. Unless you have a perfectly squared up pen blank, drilled perfect down the middle, this wont really work all that well.

A fairly simple jig I made works great... cheap and easy and squares up any and all sizes of pen kits.

Rather than me retyping it all, please go see it on my web site where it is stored.

http://woodhelp.com/Jigs.htm#SquaringJig2

Re: Making a pen without a pen mill?

#5

Re: Making a pen without a pen mill? *LINK*

Rick_Allen

>The problem with that sanding is sometimes the tube isn't square within the wood blank.

There is a product which lets you put the blank on a rod...


Universal Pen Blank Squaring Jig

Re: Making a pen without a pen mill?

#6

sharpen

John K Jordan

>> my pen mill doesn't seem to be working all that well tonight

Pen mills need occasional sharpening. When dull they just spin and burnish instead of cut. I sharpen by hand with a flat diamond paddle hone.

JKJ

Re: Making a pen without a pen mill?

#7

Thanks!

wilbur

>Thanks, John. I just came up from the basement, and sharpening my pen mill happened to be what I wound up doing. A little sharpening using my diamond bench stone, and the pen mill worked a lot better.

Re: Making a pen without a pen mill?

#8

Steven Antonucci

I take mine apart

steve antonucci

>Assume you did too, but they are a lot easier to sharpen apart than as a whole.

Before I had one, I used a skew, long point down. Honestly, I wasn't very good with a skew, so I guess I'd be much better now. you can slightly undercut the end to disguise any issues.

steve

Re: Making a pen without a pen mill?

#9

I do this without a pen mill or jig (long)

Henry (Raleigh, NC)

>I'm a newbie turner and I will be so for awhile. I turned my first pen last week. Pen turning is just like the rest of turning - you need this mandrel, that set of bushings, this kit, that drill bit. Ok I went for those items. Then of course you 'need' this jig to assemble, that jig to square it..... and on and on. I drew the line there. I just wanted to try a few pens without having them cost me $50 each.

Here's how I square the end of the blanks, even when I have been very sloppy in drilling.

- drill the blank and glue in brass tube

- mount on lathe and turn an even cylinder; the sides will be parallel to tube even if the end is not square (i.e. if you have been sloppy in drilling the blank)

- remove blanks from mandrel and then use disk sander and miter gauge to square up the ends

- remount onto mandrel and finish the process. Remember to maintain order and direction of blanks when remounting onto mandrel.

One disadvantage of being sloppy in drilling the blank is that the grain pattern can be somewhat discontinuous along the two pen parts.

To end up with a really top notch pen - well I have a ways to go. However squared up ends are relatively easy this way, even if they are a little slower.

Henry

Re: Making a pen without a pen mill?

#10

Re: I take mine apart

wilbur

>Hi Steve,

I did take apart my pen mill to sharpen it.

Regarding the skew, I thought about using it to make a shoulder cut instead of using the pen mill to square up the ends, but couldn't figure out how to go about doing it. The way I've been making my blanks is that they wind up being about 1/8" oversize for the length of the brass tube. If I was to mount those blanks on a pen mandrel and try to use a skew to trim it down, I don't see how I can tell where to make the cut.

It occurs to me that you could turn down the blanks to final shape and diameter and square up the shoulder as the last step. Does anyone do that?