Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

buying the new lathe

Posts

Re: buying the new lathe

#26

jet 1642vs voltage is NOT selectable!!

Dave (PacNW)

>The Jet 1642vs comes in either, 1 1/2 HP 110v or 2HP 220v and cannot be switched. They use different motors and Variable Frequency controllers. What You Buy is what you get. I have had the 1 1/2 H.P. version for 5 years and never felt the need for more power. I core to 14" on the low range and have not stalled out once.

Just 4 cents worth (adjusted for inflation

Re: buying the new lathe

#27

Include a switch . . .

Doc Green

>Carol, if you have not already, you may wish to consider a switch so you can turn the power off to the lathe. Otherwise, the inverter will stay on all the time.

For 220V, you need a double-pole, single throw switch. It will have four terminals.

I have a PM 3520 with such a switch. I bought it at Lowes and once installed, it looks like an ordinary light switch. It is rated at 15 amps, and at full load, the 1642 will only draw a little over 8 amps.

Caution: A four-way switch used to turn lights on and off from different places also has four terminals and is almost identical in appearance to the double-pole, single throw. Be sure you get the right item.

Have fun! ~Doc Green

Re: buying the new lathe

#28

Re: Include a switch . . .

Carol Reed - home in Strawberry

>Thanks, Doc.

On my to-do list for today is to design the power feed for the new lathe and make a list of needed items. I go into town tomorrow for shopping. I'll include the switch you described.

Any other tips, hints, desirous mods, etc.?

And, yeah, I've read Dominic's sand box ballast article. Its on the list once the lathe finds its perfect spot in the turning shack.

Re: buying the new lathe

#29

Jet 1642 stuff

John K Jordan

>- Carol, you may already know this, but like any long lathe with a stand like this, the cast iron bed can twist a bit and throw off the alignment. If the points of the head and tailstocks don't line up perfectly, the fix is usually simple: adjust the levelers on the feet to remove the twist. If you don't have levelers, shim. Cast iron is surprisingly flexible.

- If you get a big catch or a stray cosmic ray or something and the lathe refuses to spin when you pull the power switch on the front, the controller may need to be powered down then back up. Power down and wait until you hear a click (maybe 15 seconds?) then power up and all should be fine.

- Don't know if they've redesigned to fix this, but my experience and that of the local PM/Jet repair guy are the same: the mechanical parts of power switch (ring with detent, ballbearing, spring) are susceptible to clogging up with very fine dust. I had to disassemble mine after a couple of years and clean it (the disassembly was not easy). To avoid future problems, after reassembly I sealed the entire switch body from the back with saran wrap and tape. (Service guy told me he did the same.) No more problems to date. You can easily get to the back of the switch by removing the plate.

- One of the best things I did for my lathe was build a little tool tray that slides in the gap in the lathe bed. (photos below) This was real quick to make with some scraps, ply, and piece of I/O carpet and has simplified my turning life. The tray can be positioned either to the left or right of the tailstock depending on the it's use. Keeps my current tool set at hand and constrained from rolling off the bed.

- The second thing I did at the same time was top the flat lathe head with another piece of the same I/O carpet using double-sided tape. This gives my left arm a comfortable support for certain operations, helps keep things from sliding off (things tend to get placed there) and is a handy padded surface to back a piece of sandpaper when touching up the end of a parted-off spindle by hand.

Where in the world is Strawberry? Send your address.

JKJ


img

Re: buying the new lathe

#30

Strawberry is

Carol Reed - home in Strawberry

>in Arizona, at the very northern tip of Gila County, about 6200 feet, and 2 miles from the top of the Mogollon Rim. If that is too specific, about 100 miles northeast of Phoenix and about 100 miles southeast of Flagstaff. It in in the tall Ponderosa Pine tree belt and is drop dead gorgeous. Only bad part is that it snows occasionally and gets way too cold for this ol' cranky body. But I suck it up(and complain a lot! ). It is not nearly as inhospitable as where I have been the last four winters though!

There is heat in the turning shack!

I'll PM my contact information. Thanks!

Re: buying the new lathe

#31

Re: Jet 1642 stuff - thanks for the tips!

Carol Reed - home in Strawberry

>