Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

B.O.W.L.S. Bowl

Posts

B.O.W.L.S. Bowl

#1

B.O.W.L.S. Bowl

Don Orr

>This is the bowl I made for Mike Rubes' friend. I was very touched by her story and finally got this finished. It is my first attempt at airbrushing anythng. I cut out some templates for the waves. I hope she likes it. Now I just need to get it in the mail.


img

Re: B.O.W.L.S. Bowl

#2

Re: B.O.W.L.S. Bowl Bottom

Don Orr

>Underside of bowl. The bowl is about 7" diameter and 2.5" tall. Finished with danish oil, buffed and waxed.


img

Re: B.O.W.L.S. Bowl

#3

Re: B.O.W.L.S. Bowl Bottom

Hal Taylor

>Great airbrushing! I wish I could do that good.

Re: B.O.W.L.S. Bowl

#4

Re: B.O.W.L.S. Bowl

charlie belden

>Spraying the paint is the easy part - keeping it where you want it, and NOT anywhere else is the hard part. Masking down inside a bowl - with grooves in the sides can get tricky. Did you use a rubber cement "frisket" or mask off the sides with tape?

Pretty good for a first attempt - in a tricky area to mask off. And the turning ain't bad either ;)

Sure is nice to have much of the design criteria up front - and Barbara was pretty good at describing the design criteria.

Well done sir!

Re: B.O.W.L.S. Bowl

#5

Keith Tompkins

Re: B.O.W.L.S. Bowl Bottom

Keith Tompkins

>Wow Don...that's awesome.

Re: B.O.W.L.S. Bowl

#6

Re: B.O.W.L.S. Bowl

Don Orr

>Thanks everyone.

Charlie-I just used tape and paper to mask-carefully.

Re: B.O.W.L.S. Bowl

#7

Re: B.O.W.L.S. Bowl

Mike Rubes, Apex, NC

>Hi Don,

Wow!!! That is awesome! I love the "water" in the bottom. I know Barbara will LOVE it. I am just about done with the one I am making for her. I cannot remember if we emailed addresses back and forth or not or if you got one from Christine, but if you need an address, just let me know.

I really like your bowl, thank you so much for doing this.

Mike

Taking tomorrow afternoon to spin in Apex, NC!

Re: B.O.W.L.S. Bowl

#8

Don in central washington

Re: B.O.W.L.S. Bowl

don in central washington

>At the chemo center my mrs is going to One of the blank cancer bowls has been accepted by a member of another lady who's cycle was the same as ours. I will take two more this comming thursday when we have another long day there and passing on the BOWLS story and offering one to them if they so desire. One has been purchased and ACS will get the donation.

Re: B.O.W.L.S. Bowl

#9

and a quick question...

GaryG in MD

>Great work Don. What tool did you use to make those subtle spiral marks on the inside of the foot? ...Gary

Re: B.O.W.L.S. Bowl

#10

Re: and a quick question...

Don Orr

>Gary,

I used the new Sorby mini spiralling tool with the fine wheel.

Re: B.O.W.L.S. Bowl

#11

Re: B.O.W.L.S. Bowl

Don Orr

>Thanks Mike. I have your address and it will go in the mail tomorrow.

Re: B.O.W.L.S. Bowl

#12

Re: B.O.W.L.S. Bowl

Mike Rubes, Apex, NC

>Hi Don,

That is awesome. I know she will love it!

Thank you very much,

Mike

Lunch and then an afternoon of turning in Apex, NC!!