Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

? for 3520 Remote switch users

Posts

? for 3520 Remote switch users

#1

? for 3520 Remote switch users

Paul Zerjay

>When turning any large heavy object, the braking system on a 3520 seems to want to tighten a faceplate, or chuck for that matter, onto the spindle. I usually use the variable speed dial and simply slow the speed before a final stop. But when hollowing, it's a PITA to have to walk around to the front of the lathe... Are there any after-market remote switches with a variable speed dial?

Re: ? for 3520 Remote switch users

#2

Re: ? for 3520 Remote switch users

Doc Green

>Paul, not too long ago, I was playing around with my new Jet mini with a Talon chuck on the spindle. Turned the RPM's up pretty high. "Gee, that shore is smooth," says I to myself.

Then I turned if OFF ... and the chuck, which I had not "snapped" on, began to unwind and make every effort to come off the spindle. Only the tool rest kept it from hitting the floor.

Based on this, my thinking is that the braking system would tend to Loosen the chuck or faceplate. I suspect impact forces from having the tool hit projections on the blank is the cause of the tightening.

If this is the case, the remote variable speed control would not solve your problem. Just a thought. ~Doc

Re: ? for 3520 Remote switch users

#3

Re: ? for 3520 Remote switch users

Craig Daymon

>If the problem you are having is the faceplate or chuck sticking too tightly when it comes time to take it off, try spraying a shot of WD-40 on the spindle before mounting the faceplate or chuck. I tried those rings which are suppose to prevent sticking, but WD-40 works just as well or better.

Of course, doing this might mean your problem will switch to the one described by Doc. In that case, try to make good use of the set screws. (Personally, I find it useful to switch back and forth between forward and reverse, so set screws make a lot of sense for me. There is an article in the Articles section discussing set screws for the Oneway chucks...basically which screws to use.)

-Craig

Re: ? for 3520 Remote switch users

#5

Re: ? for 3520 Remote switch users *LINK*

Chuck Engstrom

>Hi Paul -- There is a remote on/off switch made by Powermatic for about $124 from Osolnik Machinery, and I think its electrical functions can be easily duplicated by DIYs. But the speed control isn't part of it.

The 3520A manual has a basic schematic showing that the speed control is a variable resistor. If you can figure out how to add an second one for a remote without compromising performance, let us all know. The full technical manual for the controller is at its manufacturer's website, see link below, and will make you think twice about messing with this thing.

Alternatively, you could relocate the built-in speed pot into a moveable box with appropriate wiring back to the controller.

Usual precautions apply: don't try this in the shower during a thunderstorm, etc. etc. and check my opinions with smarter people than me.

Best--

Chuck Engstrom


Powermatic VFC mfg's manual -- heavy reading!!

Re: ? for 3520 Remote switch users

#6

Jack, that link didn't work for me....

adrien

>Sorry, the page (or document) you have requested does not exist.

Please check the address and try again.

Re: ? for 3520 Remote switch users

#7

OOPS I got it backwards didn't I?

Paul Zerjay

>Either way a sharp start will tighten, and a sharp stop will unwind. So "sharp" is what I'm wanting to get away from.

Re: ? for 3520 Remote switch users

#8

Remote switch *LINK*

Ed Larson

>I built a switch similar to this and it has worked well for over a year. Get a water proof switch box and seal all the openings with hot melt glue or epxooy. If the links does not work, go to the mustard monster web site and look under electrical.


http://docs.google.com/View?docID=d4b7vjd_22cwwph2&revision=_latest

Re: ? for 3520 Remote switch users

#9

Re: ? for 3520 Remote switch users

Jorge Castaneda~Downeast Maine

>Paul,

I use the remote from Powermatic and I love it, as there are electronics involved, I did no want to take chances, so I bit the bullet and never looked back.

Jorge

Re: ? for 3520 Remote switch users

#10

Re: ? for 3520 Remote switch users

john lucas

>Paul it would get pretty complicated wiring wise to have both a remote with speed control and one on the lathe. it would be pretty simple to simply have one remote with speed and on/off and not have the two on the lathe headstock. Just simply extend the wires and do away with the ones on the headstock.

It's pretty simple to add just a remote switch but the variable speed control would require a switch to change between the two I think. I could be wrong on that however. Hopefully someone with more electronics can answer.

Re: ? for 3520 Remote switch users

#11

Re: ? for 3520 Remote switch users

Bill Turpin in WNC mountains

>This should work with a simple 3PDT toggle switch.


img

Re: ? for 3520 Remote switch users

#12

thanks Bill- I had to leave for work and

John Lucas

>didn't have time to think it through. I'm having to redo my remote switch as well in the next week or so. I might give it try to see how it works. I just did a hand mirror that was very scary. I had to shut the lathe off each time before I adjusted the speed because reaching for the speed knob was just flat out dangerous and stupid.

Re: ? for 3520 Remote switch users

#13

Re: ? for 3520 Remote switch users

Walter Ahlgrim

>That switch scares me! If you had something large on the lathe and pot 1 set for 500 RPMs and you accidently bumped the switch to pot 2 and it was set for 3000 RPMs you could be in big trouble before you understood what happened and could get the switch back or find the other knob. Be sure to mount it with a guard to prevent unintended actuation. It probably is only necessary to switch the center lead of the pot.

Walta


img

Re: ? for 3520 Remote switch users

#14

Re: ? for 3520 Remote switch users

Jim Terry

>I believe you want to rethink this setup. You have placed the two potentiometers in parallel. Assume each are 1K ohm pots. You have now changed the load from 1000 ohms with one pot to 500 ohms with the two in parallel.

Re: ? for 3520 Remote switch users

#15

Re: ? for 3520 Remote switch users

Walter Ahlgrim

>In most control circuit one side is ground and the other is very close to the DC power supply. And the value of the pot on ohm often just doesn�t matter much as long as current draw is not too high. 1K, 5K, 10K, 100K all will work just as fine.

He will need 3 conductor shielded cable something you will not likely find at the hardware store.

Walta


img

Re: ? for 3520 Remote switch users

#16

This link should work *LINK*

Jack Savona

>Here is the correct link to the Mustard Monster Site. The attached photo shows a VERY easy remote to make.


img

Mustard Monster Site - Electrical

Re: ? for 3520 Remote switch users

#17

Re: Response to several comments

Bill Turpin in WNC mountains

>The switches are not in parallel. Only one is in the circuit at a time.

My switch is a three position switch with off in the middle. This would require TWO accidental clicks to have a disaster. To prevent such a disaster anyway, put the unused pot at zero speed before changing to the other pot.

Walter's diagram with a one pole switch has both pots in the circuit at all times.

Jack: On another conversion on a mini lathe I learned the hard way to leave the original OEM stuff active and unchanged. Although a totally moveable remote station is nice it can be unsafe also if it overrides stops, etc that are no longer active or are mounted somewhere else.

Just about any supplier that has the pot and 3PDT should have the shielded wire also.

I have ammended my drawing to show the open contacts. For safety do not change pots while the lathe is spinning.

As always it is so difficult to explain electricals over the web. So please take the ADDY proticol.


img