Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Russ Fairfield safety discussion is

Posts

Russ Fairfield safety discussion is

#1

Russ Fairfield safety discussion is

Alan T

>one of the best posts I've seen here on safety. And the ensuing posts to his is a real education in proper lathe procedure. As a pretty long time turner I always wonder what all the safety rules are relating to turning. Is there a list that exists that mentions all the "do not do" things? Or is what Russ lists the most important items to keep in mind?

Re: Russ Fairfield safety discussion is

#2

My Daddy's Advice

Doc Green

>I've read all these posts on safety and such, and I'm reminded of a bit of advice I got from my father as we walked toward the woods carrying a crosscut saw, axes, wedges, etc. I was 14 at the time, and we were about to start cutting logs for lumber to build a new tobacco barn.

His advice was succinct and to the point: "Have some damn sense when you swing that axe."

And he was a preacher!

~Doc

Re: Russ Fairfield safety discussion is

#3

Steven Antonucci

My advice (rules for my son's) is similar

steve antonucci

>Shop rule #1:

If you don't know what it is, don't touch it.

Corrolary:

If I've never let you use it before, you better ask first...

Steve

Re: Russ Fairfield safety discussion is

#4

Re: Russ Fairfield safety discussion is

Rick_Allen

>escape. Have a plan of escape and practice that plan with your eyes closed.

bounce surfaces. Proper bounce surfaces can help an escape plan.

You don't want to translate the rotational speed into straight line speed. Soft bounce surfaces tend to increase the excitment. The spinning object which is set free of the mounting restraint can go in any direction along it's "line of fire". The object is almost always going to be deflected by tool, tool rest. banjo, lath bed... You can construct "bounce surfaces" which will direct the free object towards a containment area.

Re: Russ Fairfield safety discussion is

#5

BarbS

My dad's oft-repeated advice:

BarbS

>"Well, did 'ja learn anything?" Hmph.

Re: Russ Fairfield safety discussion is

#6

Re: Russ Fairfield safety discussion is

Wally Dickerman in Arizona

>Something that hasn't been discussed is safety by way of tool control. I'm convinced that most big bowl bustin' catches, which can be dangerous, are the result of losing control of the tool during a small catch. Happens in in instant so the turner doesn't realize it. The near automatic reaction of the turner immediately after a big catch is usually where the trouble lies.

I think that it's important whenever something occurs which was probably a result of improper tool handleing, for the turner to take time to analize exactly went wrong and why. When teaching, I always work with a student on that.

Keeping the tool tucked snugly in to the body and under the forearm whenever possible, is imperitive. It is important to always have the handle at the proper angle and have the rest at the proper height. Teaching yourself to be relaxed and not white-knuckled while turning helps a lot in tool control. Turning at speeds to match the turners turning skills is important. The experienced turner instinctively knows things that should or shouldn't be done with a tool to turn safely. It's easy, expecially for a novice to carelessly roll a gouge so that an unsupported cutting edge is exposed. A sure way to get a big catch.

Be careful out there.

Wally

Re: Russ Fairfield safety discussion is

#7

Re: Russ Fairfield safety discussion is

Alan T

>Wally, I followed your advise before about having the tool under your forearm. That was for using a hollowing tool and your advise helped me a lot. It felt a lot easier and safer to use my hollowing tool with that technique. Thanks again as usual for sharing your wisdom. Alan T.

Re: Russ Fairfield safety discussion is

#8

Keith Tompkins

Re: Russ Fairfield safety discussion is

Keith Tompkins

>Another point worth considering...many new turners don't understand the properties of wood, and even worse, refuse to give up on an unsound piece of wood....often not even recognizing there is a problem. I cringe when people post how to repair a cracked blank, or how to save a blown up piece. I've had students come to a class with their own wood blanks that were checked beyond belief, expecting to turn them. Not in my class. The best way to "save" a turning...cut in in half and start over. While I'm at it, grinding jigs should be a "must" for new turners. If the grinder slows down while sharpening, you're applying too much pressure...same when the first two inches of your cutting edge is blue. A turning forum is not a substitute for a good teacher....if you are a novice, or having trouble, find a good teacher, or at least invest in a good dvd. Learning from a friend of a friend of a good teacher doesn't cut it. Bad habits, once developed, are nearly impossible to correct later.

Re: Russ Fairfield safety discussion is

#9

Steven Antonucci

If you own 60 grit sandpaper, safety is an issue

steve antonucci

>It might sound condescending, but a good earmark for safety training is where you start sanding. If you have to use 60 grit sandpaper, odds are that you can benefit from a lesson or two (and a lot of practice) that will greatly reduce safety issues.

Aside from the dust issue, tearout is usually cause by tools being presented incorrectly, dull tools, or off bevel- all which greatly increase odds of catches, airborne wooden projectiles, and bodily injury.

There is an unconscious list of things I check every time I step up to the lathe-

Is the tool sharp?

Is the wood free of defects (od do I know what defects it may have)?

Is the wood securely mounted?

Is my lathe speed set properly?

Will the wood spin without hitting the lathe?

Can I reach the powerswitch if I need to? (I have one on either end of the lathe)

Am I OK to be in the shop?

Is there anyone home if something bad happens? Do I have a phone close by?

Am I out of the line of fire?

Is there anyone else that might be in the shop and in the line of fire?

Do I have the proper tooling to make the next cut? (7" over the toolrest with a bowl gouge means NO!)

and the list goes on...

S

Re: Russ Fairfield safety discussion is

#10

Re: Russ Fairfield safety discussion is

bowlman

>Wally and others,

I completely agree about the dangers of the white knuckle death grip. Seems like they are trying to strangle a snake. I once had a student who just didn't seem to grasp the disadvantages of the white knuckle grip, so, I excused myself for a moment and went into the house. When I returned I had a hot dog in my hand. I placed it in his hand along with the gouge handle and told him "This is your lunch ... if you like it all mushy, grip hard. If you'd rather eat a better looking dog, ease up a bit. After a few mushed weiners, he did finally seem to catch the mood.

Sometimes teaching turning is like teaching a pig to sing:

Irritates the pig and wastes your time ... but hey, whatever it takes to get the lesson across, right?

Re: Russ Fairfield safety discussion is

#11

Yes, this is what I was looking for:

Alan T

>A list like this is invaluable for all of us. Let's keep it going. ANybody care to add to this? What are the definite NO, NO's in turning. I for one am never going to wipe chips off the tool rest with my fingers.

Re: Russ Fairfield safety discussion is

#12

Steven Antonucci

Some more "good rules of thumb"

steve antonucci

>Eye protection

Face Shield (although many have seen me without one)

No long sleeves, no matter how tightly they fit

No rings

NO iPods with earbuds (I will turn with music on, but I need to be able to hear what's happening)

Nothing on the floor to trip over

Make sure the tool rest puts the CUTTING EDGE at or above center before cutting (NOT the toolrest at centerline)

make sure your RPMs match the work you are turning and your skill-speed is good, but not if you are afraid of it. Never turn faster than you are comfortable with.

Learn to listen to the sounds of cutting wood with a sharp tool. The HISS is bliss. If there isn't a hiss, go sharpen or stop to investigate why...

Steve

Re: Russ Fairfield safety discussion is

#13

Thanks Steve

Alan T

>I'm printing these out so I can remember all of them. I really appreciate it. Alan

Re: Russ Fairfield safety discussion is

#14

and more...

GaryG in MD

>Alan,

The AAW web site has a nice list. We have reproduced them on the Safety page of the MCW web site -- see

http://montgomerycountywoodturners.org/LatheSafety.aspx

In addition, you will find a number of stand-alone safety articles -- most of them based on very practical experience.

...Gary

Re: Russ Fairfield safety discussion is

#15

S-A-F-E-R ... a useful acronym

Ed Moore in SW VA

>Don Riggs often begins a demo with the acronym SAFER.

Speed - Check the SPEED before you turn the lathe on

Aside - Step ASIDE before you turn the lathe on

Fasten - Be sure to FASTEN the banjo and tool rest before you turn the lathe on

Eyes - Put EYE protection on before you turn the lathe on

Rotate - ROTATE the work to see if it clears before you turn the lathe on

Remember S-A-F-E-R, and respect the bandsaw,

Ed

Re: Russ Fairfield safety discussion is

#16

Re: S-A-F-E-R ... a useful acronym

russ fairfield

>You've been reading Kieth Rowley's book.

Re: Russ Fairfield safety discussion is

#17

Re: S-A-F-E-R ... a useful acronym

Ed Moore in SW VA

>Thanks Russ. I have no idea where Don Riggs got SAFER from, but it is quite possible that he or a friend of his got it from Keith's book. The idea wasn't mine, so I claim no originality.

Sequence Matters - This is a phrase that I use frequently when teaching. I am sure that others use the same idea or concept, but I used this when teaching calculus before I started turning.

Respect the bandsaw,

Ed

Re: Russ Fairfield safety discussion is

#18

Re: and more...

Alan T

>Gary, Thanks I'll check out those sites. I used to live in MC off Seven Locks Rd. in Potomac. I wish I would have checked out the turning club when I lived there. Thanks again. Alan