Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Vari Grind2 Instructions

Posts

Vari Grind2 Instructions

#1

George Taylor

Vari Grind2 Instructions

George Taylor

>I purchased this updated attachment at SWAT earlier in the fall and I was wondering if anyone had come up with typical settings for the various common grinds? All I got with the unit was a DVD and I thought it was less than clear. I just want to be sure I am pointed in the right direction for spindle gouges vs. side grind bowl gouges vs. traditional bowl gouges.

The unit has graduated numbers on it from 1-7. Any help would be appreciated. The Oneway sites had no documentation except for the video that was included.

Thanks

George

Re: Vari Grind2 Instructions

#2

Re: Vari Grind2 Instructions

Dave Moore

>George, I agree the info from Oneway is a little thin, however it's going to depend on the turner a lot too, and how they work.

Currently I'm sharpening deep fluted gouges at a setting between 6 and seven on the scale, and shallow fluted ("spindle") gouges at about 3.

It's still a work in progress though. I'd been hand sharpening until I got this unit fairly recently, so I'm still feeling my way with what it can do. Those settings do work OK though, for the way I turn.

Re: Vari Grind2 Instructions

#3

Lyle Jamieson

Re: Vari Grind2 Instructions

Lyle Jamieson

>George, you are in for a long learning curve. I am very well versed in sharpening by hand and with jigs. I set them up from scratch all over the country as I travel demonstrating and for classes I am teaching. I have set up hundreds of systems. With that said I had a very hard time getting the Vari grind 2 set up to do my Jamieson signature grind. I finally got it set up correctly but it was very hard and counter intuitive. When you move one element to correct the tip or side angles the other elements are out of wack. Very different then the wolverine, True grind or Packard systems. The Vari Grind is good for a beginner to use but I cant imagine a beginner being able to get it set up correctly. If you are an experienced turner then there is no need to keep the grinding in dead center of the wheel. In fact we intentionally use the entire surface of the grinding wheel to keep it from getting a rut in the middle. Just dont go off the edge of the wheel. If you have a tremmor or have difficulty controling the sharpening action then the Vari Grind 2 would be a God send, to keep you from getting hurt.

Re: Vari Grind2 Instructions

#4

Jesper, Denmark

Re: Vari Grind2 Instructions

Jesper, Denmark

>http://www.thompsonlathetools.com/sharpening.asp

Easy to follow instructions.

Re: Vari Grind2 Instructions

#5

Lyle Jamieson

Re: Vari Grind2 Instructions

Lyle Jamieson

>That instruction is for the vari Grind (1), the (2) is a whole new ball game.

If you want instructions to set up the (1) you only need to know two things. Fisrst, the tip angle is set by moving the jig arm. Second, the side angles of the swept back grinds are set by sliding the basket/pivot point in and out. Its not that simple with the (2)

Re: Vari Grind2 Instructions

#6

Re: Jamieson signature grind? I haven't...

Jamie Donaldson

>....seen that one Lyle, so could you post a close up photo for reference?

Re: Vari Grind2 Instructions

#7

Re: Vari Grind2 Instructions

Dave Moore

>Oops! I got those numbers reversed George.

Should be spindle gouges about 7 on the scale, and bowl gouges about 3.

My bad, I was sleepy.

Re: Vari Grind2 Instructions

#8

Lyle Jamieson

Re: Jamieson signature grind? I haven't...

Lyle Jamieson

>Im Having a hellofatime, this is the third try at it. hope this one goes out there.

I can't get a photo to load I will have to get my talented wife to help me figure it out. It flashed a quick error note, I didn't have time to read, that said something about format. I have a PDF file of it on my desk top I was trying to use. You can see it on my web site www.lylejamieson.com. Look down toward the bottom of the store section.

The difference in my grind is twofold. First the side grind is tilted in slightly. This is not visible in the photo. The tilted in side grind gives a bigger, sweeter, easier to control bevel support all the way around the tip. This makes it easier to put the handle down in a pull cut mode AND still have the bevel support when you do the bottom of a bowl. This allows you to make a nice sweeping line with the bevel directing the cut instead of white knuckling it around the bowl shape. How?? To make the side angles tilt in, move the basket/pivot point away from the grinder. Try moving it 1/4 inch and see what a difference it makes. If you are happy with the tip angle you have it will be necessary to move the jig arm now because moving the basket will have changed your tip angle too.

Second, is the wing does not have a hump. The swept back wing from the tip to the heel of the wing is almost a straight line as seen in the side view photo. Assuming the grinding jig is set up correctly all you need to do to remove the hump is grind the high spot down. The advantage of removing the hump is huge. When you start a push cut the bevel is almost immediately supported. With the hump, the wood is being cut and the bevel is still out in mid air and you often will get a skating catch. When you grind the hump down the tip of the gouge will appear to be a little more pointier, and that's OK. All four cuts I describe in my Bowl Basics DVD are easier with the hump removed, push, pull, scrape, and sheer scrape.

Re: Vari Grind2 Instructions

#9

Grind image! 

Stephen Mushinski

>


img

Re: Vari Grind2 Instructions

#10

Lyle Jamieson

Re: Grind image!

Lyle Jamieson

>Thank you Stephen!! By the way, I like a tip angle at about 60-62 degrees. The tip is measurable with a protractor.

Re: Vari Grind2 Instructions

#11

Re: How about that! I've been using ......

Jamie Donaldson

>...the Ellsworth/Jordan/Jamieson/Jamie grind for years and didn't know its full name!

Re: Vari Grind2 Instructions

#12

Re: How about that! I've been using ......

russ fairfield

>Lyle mentions that the wings are not the same, and that they are somewhat lopsided.

Several years ago I saw Melvin Firmager using a gouge that had one of the wings totally removed. I made one of these by removing the left-wing back about an inch, and have been using it ever since. It has the advantage of being able to better see inside of a bowl, and there is no flute for the chips to get clogged in. I can take a humongous cut without the tool clogging. It doesn't cut any different because I have done nothing to the tip or the cutting wing.

It works equally well for making big roughing cuts on the outside of a bowl, but can only be used for cutting from the rim to the foot, unless I stand on the other side of the lathe and work Left Handed.

Re: Vari Grind2 Instructions

#13

Well, that explains that

Gary Evans--Tallassee TN

>I have a used bowl guage that I got when I bought my Woodfast. I never could figure out why the previous owner cut one of the wings clean off.

Gary

Re: Vari Grind2 Instructions

#14

Weld the leg at 23 degrees *LINK*

Jerry Hall

>See Wolverine Varigrind set up video in link. Get a copy of referenced article (AAW magazine, by Kirk DeHeer "Sharpening Demystified," Volume 21 Issue 4, Pages 32--34) available by contacting http://www.woodturnerscatalog.com

Works for me. Just kidding on the weld. But repeatability is the key. Set the leg and leave it alone. The templates described in the article for setting the extension on the arm are a nice idea and also helps a bunch with repeatability and fast refreshing of the edge in one light pass or two.

Also great overall video on sharpening here:

http://www.woodworkingonline.com/2008/09/23/podcast-37-turning-tools-sharpen-your-skills-with-sharp-tools/


Wolverine Varigrind Setup Video

Re: Vari Grind2 Instructions

#15

Lyle Jamieson

Re: How about that! I've been using ......

Lyle Jamieson

>Sorry Jamie, they are not the same, and there is not a good or bad, better or worse, they are different and are used differently. The devils in the details. I dont know what you use but:

David has a hump and uses it for his finishing cut inside a bowl that I dont do, and I cant do his cut without the hump.

John uses the bowl gouge set up more like the wolverine directions would leave. The side angles are steeper and not as tilted in as David and I use.

Others use many different grinds. Trent uses a grind that is not symmetrical, only one side swept back.

You asked what made my gouge different and that is what I addressed. I didn't say the others were inferior in any way, we all use them for different cuts and with different techniques.

Re: Vari Grind2 Instructions

#16

Re:Well Lyle, it appears that the Jamie......

Jamie Donaldson

>....grind is virtually identical to yours, except I often grind a relief at the heel to facilitate shorter radius cuts. We usually adapt what profile works for our particular needs, and that's all that matters.

Re: Vari Grind2 Instructions

#17

Lyle Jamieson

Totally agree......

Lyle Jamieson

>