Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Thin parting tool advice

Posts

Thin parting tool advice

#1

Thin parting tool advice

wilbur

>I'd like to get a thin parting tool for parting off the lid of turned boxes. I'm trying to decide between two Sorby 1/16" models -- one has a short steak knife type handle, and the other has a longer handle and a flute. The main reasons I'm interested in these two are (1) I have a credit at Woodcraft, and these are the ones they have, and [b] Doug Thompson doesn't make one. :@)

The fluted Sorby parting tool, however, is close to twice the price of the plain Sorby parting tool. Is there much difference between the non-fluted and fluted parting tools?

Re: Thin parting tool advice

#2

Re: Thin parting tool advice

eliot d

>How handy are you? You can easily make your own from a band saw blade or an old knife.

Re: Thin parting tool advice

#3

Re: Thin parting tool advice

Dick Coers

>The fluted one will eat up your tool rest. I have the "steak knife" one and like it a lot.

Re: Thin parting tool advice

#4

Re: Thin parting tool advice

Bill Grumbine (Kutztown PA)

>Wilbur, I have the fluted one, and it is well worth the money. It has not been a problem for my tool rest, as the flute is used in the up position. Mine is approximately 13 years old, and still has at least as much life left in it as I have already used. I think the fluted one gives a better cut than the non fluted one.

Re: Thin parting tool advice

#5

I agree with Bill " NM"

Dennis Yoder

>

Re: Thin parting tool advice

#6

Re: Thin parting tool advice

nick

>How do you sharpen the fluted type?

Re: Thin parting tool advice

#7

Re: Thin parting tool advice

Bill Grumbine (Kutztown PA)

>There are two bevels on the thin fluted tool. The top bevel is fluted, the bottom is not. Sharpen the bottom bevel, and the edge where they meet, including the flutes, will be sharp. Sharpen the top flute by mistake, and you end up with a very expensive non fluted parting tool.

Re: Thin parting tool advice

#8

Re: Thin parting tool advice

Dave Peebles Lyons, Ohio!

>Hi Bill,

I have one of the Sorby's too, and the instructions point to using it flute down. Using it this way will make a mess of the tool rest. It sits in the rack most of the time, but it does cut very cleanly.

Here is the info similar to what I got with mine... we may be talking about different tools entirely. :)

----------------------------------------------------------------------

Fluted Parting Tools: An even more recent innovation is the fluted parting tool and versions of this are produced by both Henry Taylor and Robert Sorby. The advantages to both designs is that the wood fibres

Standard fluted parting tool - similar for both Taylor & Sorby Designs.

bordering the cut line are severed cleanly before the main

2mm parting tool by Robert Sorby

part of the blade clears out the bulk of the timber from the kerf. This results in a very clean cut surface which normally does not need subsequent cleaning up.

The Taylor model HS2 and Sorby 832H - 3/16 are similar in design with a flute running the length of the bottom edge. Both are used with the flute down onto the toolrest (this can cause damage to the toolrest surface, which should occasionally be dressed with a file .) These should be sharpened by grinding the bevel (front) face only. The tapered profile serves, like the diamond-section tools, to reduce friction in the cut.

Dave

Re: Thin parting tool advice

#9

Simple trick for fluted tool

David Belser

>I have the 2 different fluted parting tools and prefer them to plain/flat. They *WILL* chew up your tool rest if used without any protection. However there is a simple solution to this problem. I've used a short piece of PEX tubing that has a slit in it. I slide the flute side into the tubing and it prevents the tool rest from being chewed up. The tubing was leftover from a heating system install, but you should be able to get a short bit of stuff from the hardware store. I'm sure the type doesn't matter as long as it's hard to cut.

One of the parting tools came with a bit of plastic to protect the flute during shipping. I used this until it fell apart - hence the switch to something more substiansial.

I haven't tried using it "upside" down, but will see how that works out.

And yes *BE CAREFUL* when sharpening - I did touch the flute to the sharpening belt and then has to grind away about 1/8" to get back to a good section of flute.

Re: Thin parting tool advice

#10

Re: Thin parting tool advice

Bill Grumbine (Kutztown PA)

>Well I guess I am a moron then. This tool was handed to me by a friend as a thank you for teaching him to turn a hollow form, and then letting him use my lathe for his first one, way back in '96 or '97. I just assumed that the flutes would go up, since putting them down moves them out of the prime cutting area (not to mention dinging up the tool rest!). I never read any directions for the thing. I guess that worked out to my benefit, huh?

Re: Thin parting tool advice

#11

Re:I used one of these fluted tools.....

JamieD

>...with the flute up, and got a gargantuan catch when the sharp flute edge hung in the kerf- scared the pee out of me! I subsequently modified the grind to place a flute on an angle at the tip, then ground away the flute on the bottom to prevent destroying my tool rest, again! I noticed later that a grind configuration similar to mine was available from Sorby, or was it Taylor?

Re: Thin parting tool advice

#12

Re: Thin parting tool advice

wilbur

>Thanks, all -- I ordered the Sorby fluted parting tool. I'll try it with the flutes up and down to see how it works. :@)

Re: Thin parting tool advice

#13

Re: Thin parting tool advice

eliot d

>Oh, come now, nobody on this site would say you're a moron! Other sites? I don't know! Have a great Holiday season -- and ,yes, that does include Christmas!