Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Cleaning out worm holes

Posts

Cleaning out worm holes

#1

Cleaning out worm holes

Chris Krohn

>I have been turning a fair share of root burls and with it comes a lot of worm holes filled with, whatever it is they are filled with. I have a feeling it is something I should be cautious of. After spending about eight hours on my most recent bowl clearing out the voids with a nail and a brush, i felt like there was some better way to get this crap (pun intended) out of there. Perhaps some sort of thinner or cleaner that has been successful in the removal.

Re: Cleaning out worm holes

#2

Re: Cleaning out worm holes

Roger

>An air compressor with blow gun and fine wire works for me.

Roger

Re: Cleaning out worm holes

#3

Re: Cleaning out worm holes

john lucas

>I just put thin CA on the holes to solidify whatever is in there and then turn it.

Re: Cleaning out worm holes

#4

Re: Cleaning out worm holes

Barry Irby

>Try wetting it. With water. This is a really dim recollection, but somewhere along the way I turned something that had hundreds of packed holes and I wet it, as in dipping it in the water for about ten seconds and the stuff swelled up and came out. Then I blew out the remainder. This is such a poor memory, I would try wetting a small area first to see what happened. There might be different types of worms with different types of crap too.

I have also drenched several with CA and left them in place.

Re: Cleaning out worm holes

#5

Re: Cleaning out worm holes

John Veerkamp, Western Mo

>dental picks work well. Get used from your friendly dentist. or some craft suppliers sell sets. use an old toothbrush and you can clean out the dross effectively. It is sometimes tedious, but the results are well worth it. An very wormy piece of mesquite makes for a uniquely beautiful piece.

John

Re: Cleaning out worm holes

#6

Re: Cleaning out worm holes

doug williams

>I am in the process of making a bible stand out of walnut for a church and ran into some worm holes also. I got a used dental pick which really gets into the holes to loosen up the frass, then dropped in turquise powder and a drop of thin CA on top hit with accelerator and its set. The shape of the worm holes with the turquise inlaid makes it an interesting piece. Some of the holes taper out to nothing and its hard to fill the hole completely as you will see a little glue but no stone, I took a small dremal bit and keeping the same profile squared up the hole so the powder had something to adhere to and it looked a lot cleaner.

Re: Cleaning out worm holes

#7

Re: Cleaning out worm holes

Scott Greaves in Blackfoot Idaho

>Lay down on your back, and hold the wood up in the air, directly above your head. Open your mouth. Fate would not let an opportunity like this go by, and all of the disgusting crap in the wood will immediately fall into your mouth. Sad but true!

Oh, and if you use the suggestion of blowing it out with compressed air, and your mouth is open, I can guarantee where the stuff will land! Been there, done that!

Happy Thanksgiving!

Scott.

Re: Cleaning out worm holes

#8

Re: Cleaning out worm holes

Tery Scott

>I just get brass nails and whack them into the holes or drill more holes to make the pice look like the holes are meant to be there

Re: Cleaning out worm holes

#9

Re: Cleaning out worm holes

Chris Krohn------WebKitFormBoundarycqcnpI4Z6bMgmH+

>Or like I did, not once but three time, pick a bunch out and blow really hard and get a bunch in your eye. :)

Re: Cleaning out worm holes

#10

Re: Cleaning out worm holes

Chris Krohn------WebKitFormBoundarycqcnpI4Z6bMgmH+

>What type of fine wire? The plastic kind? Dont the others scratch the surface of the wood?

Re: Cleaning out worm holes

#11

Re: Cleaning out worm holes

Roger

>I use piano wire. It's stiff enough to work well. Use it before final sanding steps and scratching isn't a problem. Dental picks work well also. various catalogs have them, or you could check with a dentist for used ones. I just happen to have piano wire, so thats what I use. Check with piano tuners in your area. Most should have rolls of different gauge wire for replacing or restringing pianos. Good luck.

Roger