Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Clewes Does Ogees

Posts

Clewes Does Ogees

#1

Clewes Does Ogees

charlie belden

>Jimmy Clewes Does Ogees

Had the pleasure of attending another day long demonstration by Jimmy Clewes. In a small venue with maybe 30 attendees it�s an up close and personal experience, apparently quite different than a symposium demonstration with 150 to 300 attendees.

Jimmy�s a friendly down to earth guy and not much into artsy fartsy - which is not to say that he doesn�t have an eye for fair curves and aesthetically pleasing shapes and forms. This demonstration made that quite clear - applying an ogee - to three very different demo pieces - a shallow bowl, a natural edge vase with stem and foot and a three arcs, quarter twist, candle stick holder - not a trivial thing to do.

The first piece started with an english walnut round blank - about 12� in diameter and maybe 3� thick - with a crack in the bottom third and a 1/2� notch in the top�s rim - the best looking grain being on the cracked end.

That�s where the sharing of his insights started - with the wood - and working with what you�ve got in front of you. Some would have skipped this blank and gone looking for a more sound blank. But a good turner will find a way to get the best piece possible out of what he�s got - even if he�s limited by the type of piece to be turned. In this case it was to be a shallow wide rimmed bowl - with an ogee profile.

Begin with the wood and the basic criteria for the piece - and THEN start making decisions BEFORE picking up a gouge.

Decide which face of the blank should be the bottom and which the top. You want the nicest grain on the bottom - so all that pretty grain doesn�t end up on the floor as shaving. You�ll also want to mount the blank between centers with the BOTTOM on the TAIL STOCK END where you can more easily true up the bottom face - and then turn the foot - along with the shallow �dovetail� recess for holding the blank later in a chuck - using expansion chucking. (This is the first of many critical steps which can make getting to the finished piece easier and safer - or a nightmare of What The Hell Am I Going To Do Now? - AFTER dodging a flying turning! )

[ This attention to details - and taking the time to point them out, along with why they�re important - and encouraging questions - is why I find Jimmy Clewes demonstration so valuable and worth every penny of the admission price. ]

Decide how you will hold the piece for outside shaping AND inside hollowing BEFORE you mount it on the lathe initially- so you don�t find yourself in a box canyon with no way to get to the finished piece.

Decide the diameter of the foot and its height. The foot is important. It give the piece lift and meet a critical requirement for a bowl - that it sit flat and stabile, not rocking or tippy.

Decide how you will proportion the ogee curves between the top of the foot and the rim of the bowl, taking into account the rim thickness you have in mind.

:

:

The list of subtle and not so subtle things to consider - and that he points out - goes on and on - as does the pages and pages of notes to go through later.

I don�t know what a Jimmy Clewes demo in a symposium setting would be like - but with a group of 25 to 30 people - he puts on quite a show - including a very Las Vegas element - and delves out hard won knowledge from experience - by the bushel. If you�re club is looking for a great demonstator seriously consider Clewes. If you get ANY chance to watch this guy in action - take it!

Re: Clewes Does Ogees

#2

Dick Hines

Re: Clewes Does Ogees

Dick Hines

>Charlie, I saw Jimmy at the NC symposium and it was standing room only. People were taking chairs from other demo rooms. I expeted the fire marshal to show up and run half of us out of the room.

Jimmy did a great demo too.

He will be in Richmond, Va next April for two days. Can't remember the dates but will post as it gets closer to April.

Re: Clewes Does Ogees

#3

Mike Stafford

Re: Clewes Does Ogees

Mike Stafford

>I also saw Jimmy in Greensboro during the NC Symposium. It was tight in the room when he demoed the oriental box which he turned from a block of canary wood. Those guys sitting directly in front had mucho mas cojones as Jimmy so aptly pointed out.LOL

I was slightly to the left in the front row and had a fabulous view of how he used his tools. He is wonderful teacher and I wish I could take a class with him sometime.

I was also able to see him in the vendor area at the AAW symposium in Richmond. At the time I was there only 6 people were watching and he actually let some of us try some of the cuts. That was worth the price of admission as well.

I think his videos exemplify what a terrific teacher and turner he is.

Re: Clewes Does Ogees

#4

In Riverside Sunday *LINK*

Ron McKinley

>Jimmy will be at the Inland Woodturners in Riverside this Sunday the 22nd at 9:00pm. We had him last year and everybody wanted him back. He was really fun in the vendor area in ABQ back in June. Always a crowd around him........Ron


Inland Woodturners