Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Turning in reverse

Posts

Turning in reverse

#1

Turning in reverse

john lucas

>I turn my mirror body's in reverse. This lets me turn downhill with the grain since I want the middle thicker than the outer edges. I've done this a lot but today I forgot to fully tighten the chuck. Usually I seat the chuck and then use the chuck key to tighten the chuck against the face. That has served me well over the years and not had a chuck come loose.

However today I forgot to tighten it and it came unscrewed hitting the tool rest and burned the center portion.

Oh well I was able to save it but of course it's thinner than I intended it to be.


img

Re: Turning in reverse

#2

saved mirror

john lucas

>This is a little different than most of my mirrors but it was fun. I turned away the burned section and then beaded the rest.


img

Re: Turning in reverse

#3

Re: saved mirror

Texian

>Good save John. Cool mirror.

Re: Turning in reverse

#4

Re: saved mirror

don lewonczyk

>Nice save John, you didn't show us that little trick at Duck River. Good thing since I was sitting up front. The mirror is really nice and so were the ones you brought with you for show. DonL

Re: Turning in reverse

#5

Explain t his Turning in reverse

jake Niedling

>John,

With the mirror back being side grain, why does turning in reverse matter with this cut? Are you also standing on the backside of the lathe when you do this? Please explain, you know I am old and slow.

Jake

Re: Turning in reverse

#6

Re: saved mirror

john lucas

>Don I did show the trick of turning in reverse. Remember when I walked around the lathe and turned with the lathe running forward but I was standing on the backside of the lathe turning from the middle of the mirror out. Then I said of course if you have reverse you can do the same cut but stand on the front side of the lathe. You must have been one of the ones who was sleeping. :)

Re: Turning in reverse

#7

Re: Explain t his Turning in reverse

john lucas

>Jake your not as old as I am but you might be slower :) I like to make my mirrors narrower at the edges and thick in the middle. If you turn from the outside of the blank toward the middle you are turning into the grain or what I call uphill. If you turn from the middle out to the edge your going with the grain or downhill with respect to the grain.

To do this I from the normal position I had my arm way out in space and it made it difficult to control the tool. Then I discovered that I could stand on the backside of the lathe and turn from middle out and get the same cut. However now the tool handle is riding on my hip. I get much more control that way.

If I turn in reverse I can cut from the middle out toward the outboard side but I'm standing on the front of the lathe.

If that doesn't make sense I'll show you on Wed. John Reiver called in a panic looking for a demonstrator so I'm going to demonstrate turning for furniture.

Re: Turning in reverse

#8

Re: Explain t his Turning in reverse

Dave Belser

>Ahh, that explains it. Was going to ask also. So you can do the same sort of cut (center to edge) with the lathe turning normal, it's just not as good of a position.

Did you get to see the Japanese turning at the AAW symposium in Portland OR? They routinely swap the direction of the lathe, it was quite impressive.

- Dave

Re: Turning in reverse

#9

Re: saved mirror

don lewonczyk

>Oh yeah John, I remember now and we were looking out your better side!!! You are correct sir, I did doze off once or twice but it wasn't because or your demo I was just bone tired and lucky to get home safe in that rain. I wanted to meet you since we have been exchanging email from time to time and on WC,so it was nice sorry I couldn't stay up with you. Take Care, DonL

Re: Turning in reverse

#10

Ok- Not the lathe running in Reverse

jake Niedling

>John,

I was thinking that you reversed the rotation of the lathe, that is what was causing my mis-understanding. I understand the cutting down hill thing from the center out to the edge. What is that old saying " I think so therefore I am confused ". That is me some days.

Thanks Old Buddy,

Jake

Re: Turning in reverse

#11

Re: saved mirror

john lucas

>One of these days I'll plan to drive down and meet you. Your on the way to my friend who lives in Fort Payne, Al.