Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Beall buffing and beeswax

Posts

Beall buffing and beeswax

#1

Peter Charles Fagg (UK)

Beall buffing and beeswax

Peter Charles Fagg (UK)

>Friends, I have just purchased the basic Beall kit with the 8 inch wheels and the blocks of buffing compound.

My questions are:

Normally I finish ALL my bowls, dishes and platters with Pure Beeswax. (Melted on to the surface)

(1) Does this mean that before I can use the buffing system I must remove the beeswax from all older stock before buffing?

(2) Can I use pure beeswax instead of the Carnauba supplied?

(3) Can I use beeswax polish that is blended with Pure Turpentine? (Soft Wax)

I realise that experimentation is the key to learning but I have no wish to ruin any of the buffing wheels in the process OR produce a worse finish than I already experience!

Your thoughts would be appreciated, Peter.

Re: Beall buffing and beeswax

#2

Re: Beall buffing and beeswax

Lee Buck

>Peter, I finish many pieces with a beeswax/walnut oil paste I make myself; I'm a beekeeper. I see no point to using the tripoli or diamond after applying the paste. I sometimes use the wax wheel to buff a piece after the paste. I would not use a wheel that has carnuba on it. I believe the much softer beeswax would make the wheel less effective when used to apply carnuba. Applying pure beeswax with the buffer would work. Humbly submitted as I have little real knowledge. This is just what I do.

Re: Beall buffing and beeswax

#3

Peter Charles Fagg (UK)

Re: Beall buffing and beeswax

Peter Charles Fagg (UK)

>Lee, thanks for the response.

It looks as if I shall have to dedicate the wax wheel to only beeswax?

Regards, Peter.

Re: Beall buffing and beeswax

#4

JL

Given the relative softness of bees wax..

JL

>that probably is a good idea.

I use (upon occasion) a mixture of bees wax and carnuba wax for polishing flat work. But I usually use old rags.

Has anyone ever tried to clean a buffing wheel or are they sort of consumable?

Re: Beall buffing and beeswax

#5

Re: Beall buffing and beeswax

Barry Irby

>I think that's your answer. Dedicate a wheel to beeswax. Not sure, but I think it would be a PITA to change back and forth form carnauba to beeswax. Fairly sure it would ruin the carnauba.

The wheels are available form other sources that might be less expensive.

Re: Beall buffing and beeswax

#6

Re: Beall buffing and beeswax *LINK*

russ fairfield

>All wax is better the thinner it is. If it feels like wax, it is too thick.

All wax is better for a good buffing. The softer beeswax will respond better to a good brushing with a stiff bristle brush, but it will also look better after buffing. The thinner coat of wax will have a better gloss that will last longer because it is thinner.

Buffing a carnauba over the softer seeswax will only leave a softer wax on the surface than if you used harder carnauba by itself. Try it. Any mixture of hard and soft wax will take on the properties of the softer wax to the degree of how much of it is used. In this case, the only difference is that the gloss will be less than if you used the Carnauba by itself.

I am working on some wax pages on my website. They aren't complete yet, but there is enough there to be helpful.


Everything I know about wax

Re: Beall buffing and beeswax

#7

Peter Charles Fagg (UK)

Thankyou for all the advice!

Peter Charles Fagg (UK)

>My thanks to all who responded, it appears that it will be very much an experiment to find the best option.

Thanks again, Peter