Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Warped blank question

Posts

Warped blank question

#1

Warped blank question

Barry Irby

>I should know this, but I don't seem to recall. (CRS?)

If I rough turn a wet blank and get a bowl that is 12" in diameter and a little over an inch thick, when it dries and warps to an oval, will it be something like 12 1/2" by ll 1/2"? In other words, longer than it was originally or will it be something like 12 by 11. (not longer that the original diameter? I have some walnut blanks drying. Just wondering.

Re: Warped blank question

#2

Re: Warped blank question

John Lucas

>Depends on how it was cut from the tree. If you assume that it is a side grain vessel (grain runs perpendicular to the bed of the lathe) and the grain was balanced. it will warp somewhat evenly into a football shape. The pith areas will get longer and stick up while the side will get shorter and move down. That's how the hat turners get their hats to fit our non round heads.

Re: Warped blank question

#3

JL

Appearance versus reality...

JL

>I think that if you put a tape on your blank, you might find that the actual difference was somewhat less. For a 12" piece, it might be only 1/2" (12 1/4" x 11 3/4") - it just looks like more. I've always been surprised at how little you have to take off to round them up again.

When I have green turned leg blanks (2" turned dimension), they typically go out of round by about 1/16 to 1/8" at the 2" bulb. Your eye can usually see about 1/32" of difference.

Re: Warped blank question

#4

Warp varies with species as well

John Lucas

>I have some rough turned Wysteria bowls that are so out of round they cannot be put back on the lathe. I will have to carve them.

Re: Warped blank question

#5

Re: Warp varies with species as well

Wally Dickerman in Arizona

>It does depend on the wood. Mesquite, our most stable wood, moves very little. Pacific madrone, our most unstable wood, will do crazy things. I once thin turned a wet medrone bowl and just let it do what it wanted to. It ended up looking a lot like a hospital bedpan.

Wally

Re: Warped blank question

#6

I haven't seen a turned bedpan-scary image

John Lucas

>

Re: Warped blank question

#7

another craft show possibility

bob davis

>

Re: Warped blank question

#8

Leo Van Der Loo

Re: Warped blank question

Leo Van Der Loo

>Wood does not get longer, you can't stretch it either.

The sides will get thinner, and shorter in circumference, so it will pull on the ends and become lower on the sides.

Depending on how much heart and sapwood you have and the species, the amount of distortion/shrinking will be different, most are in the 8% to 12% area in the circumference shrinking.

All this is assuming sidegrain turning, not endgrain.

Re: Warped blank question

#9

Re: Warp varies with species as well

charlie belden

>Wally wrote

I once thin turned a wet medrone bowl and just let it do what it wanted to. It ended up looking a lot like a hospital bedpan.

====================

Don't recall the DaDa artist, but he hung a white porcelin urinal on the wall and titled it "Fountain". You could call you madronhe bedpan piece "Pool" - and it would have made about as much sense under the last administration as "Fountain" did during the insanity of the first World War.

Re: Warped blank question

#10

Re: Warp varies with species as well

Barry Turner

>Keep moving those Wisteria blanks around the shop. If they ever take root, you'll have to burn your shop to stop it.