Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Apricot?

Posts

Apricot?

#1

Apricot?

Dave Moore

>I just today lucked(?) into a really big apricot blowdown. I was able to cut about fifteen pieces 12-14 inches diameter and four pieces from the main trunk in excess of 20 inches each. I could not pick them up unaided even when bucked to length equal to the diameter. This was a very old tree, probably planted in the early 1900s would be my guess.

It's pretty wood, kinda orange colored, with just a smallish heart shake here and there. Still quite green, even though it blew down in the spring of this year. The heart is radically off-center on several of the pieces.

Anyway, I've never worked apricot in my life, either as flatwork or in the round, so am wondering what to expect, especially with regard to drying roughed bowls. I plan to core them out wherever I can.

Average relative humidity hereabouts is pretty low, usually down around ten of fifteen percent.

Anybody been down this road?

Re: Apricot?

#2

Re: Apricot?

Barbara Gill, Remlik VA

>Dave, even if the tree had been down for years there would have been no appreciable drying except possible at the end of the logs and near the bark. For sawing, the less time the tree has been down, the better.

Most orchard type trees are inclined to splitting with enthusiasm. They also often warp with the same attitude. I would rough turn the pieces as soon as possible, turn thin hollowforms also as soon as possible. I also would not cut the chunks to be turned until you are ready to turn them. Cover all end grain with Anchorseal; don't forget where branches were cut off.

I have never turned Apricot however many years ago I sawed some Peach into boards. They dried without incident. You are fortunate to have the wood.

Re: Apricot?

#3

Re: Apricot?

Dick Coers

>What Barbara said, plus; Get the whole log sections split in half through the pith so no major splits can get started. If I do cut some into bowl blanks, I wrap them up with newspaper. That slows the drying even more. You have to balance too slow of drying and mold, versus too quick of drying and cracks. I would also remove as much bark as possible, as the log probably has a fair number of critters chewing away under the bark, heading inward.

Re: Apricot?

#4

Re: Apricot?

Dave Moore

>Barbara, thanks.

Yes, that's my experience too with most fruitwoods, they're pretty frisky, especially apple. I have been assuming the apricot will behave similarly.

It's so dry around here that I often stash roughed bowls under the house where the water cistern is located for a few months before bringing them out into the real world. It's cool and humid down there. This really helps, but with apple especially I still lose more than I would like, with or without anchorseal. (I have not found it to make much difference here actually, though I know others use it with great success)

Right now the log sections are bagged in plastic, to buy me some time, and indeed I will cut the blanks as I go, four or five at a time is my usual routine.

I may start by finish turning some of the smaller sections green, with thin walls, just to see what happens. With the logs bagged as they are, I have some time to clear the decks of current projects and then play around a bit experimentally.

Thanks for the reply.

best

d

Re: Apricot?

#5

You could use the Bob Uecker method.... *LINK*

David R Smith, Longview, WA

>...of catching knuckle balls. He said to wait until the ball stops rolling and then pick it up. You can wait for the wood to stop cracking and twisting then turn what is left in usable pieces. All fruit woods are a pain but apricot is as bad as flowering plum sometimes called horse plum.

Many people have had good success using the alcohol drying process for drying roughed out bowls and turning squares. You can find more info at the alcohol soaking blog which I have list below.

Good luck.

Dave Smith

Too pooped to work, too poor to quit in Longview, WA.


Alcohol Soaking Blog

Re: Apricot?

#6

Re: You could use the Bob Uecker method....

Dave Moore

>heh heh

I remember Bob Uecker. Funny guy.

I could use his approach, I suppose, if what I want is five thousand sets of earrings. Not sure I'm up for that kind of therapy though.

:)

Re: Apricot?

#7

Re: Apricot?

RPE

>I've turned old and green Apricot. It is beautiful wood. It will warp like the dickens however. I had one platter invert on me. It finishes really smooth. The older wood I turned had every color in it from black to white.

Re: Apricot?

#8

Re: Apricot?

R Payne

>I have done some flat and a little turning with apricot. It takes forever to dry. It does tend to warp but in my experience it doesn't split too bad. I've let a number of pieces sit without sealing the end and didn't have problems with splitting or checking.

There are a number of insect that like to eat on apricot wood. Check it cary carefully for evidence of insect activity. Removing the bark will help with that.

So far as working it, it likes really sharp tools and you need to keep your tools sharp. I've found it will dull them quickly.

ron

Re: Apricot?

#9

helpful, thanks

Dave Moore

>Ron, that's helpful, thank you. Warping I can live with. I'm just hoping it doesn't split like apple. Sounds like it may not be in that league.

We'll see.

Re: Apricot?

#10

Re: helpful, thanks

R Payne

>The apricot I've worked with tends to check some if I cut through the pith without any major splits and if I don't it may or may not end up with one bit split down one side to the pith and a little checking. That is fairly easy to saw around. I usually expect to take about an inch off each end due to checking.

I've also done some with apple. I've had it split just thinking about picking it up. Apricot is nowhere near as bad as apple.

It is a beautiful wood when finished.

ron