Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Lathe on casters

Posts

Lathe on casters

#1

Lathe on casters

Ted Evans

>Hello Everyone,

Like a few others, I suffer from a lack of room for my tools. All of my flat working tools are on casters so they can be moved when needed. I know it is not ideal for the wood lathe, a Jet 1642EVS, but is there any reason why it should not be done under any circumstances? Has any others tried this and if so, would you care to share your experiences, suggestions and/or comments?

Bear

Re: Lathe on casters

#2

Re: Lathe on casters

Ed Moore in SW VA

>I have my Oneway 1018 with extension on casters and a Jet 1220 on casters. It works great for each of them. However, I didn't put the Robust on them. ;^D

I get the excellent red wheel casters from Woodcraft and find that because they lock in two directions, roll and swivel, they work very well.

My two clubs, Blue Ridge and Smith Mountain Lake, each got a Jet 1642 and put these casters on them. It works great for most of us, but demonstrators who are vertically challenged find it to be a little high with the casters.

Ed

Re: Lathe on casters

#3

Casters work great and *LINK*

Jerry Hall

>this link (toward the bottom of the page) shows lots of good ideas for the big brother of your lathe, the Mustard Monster. Most of these have been used also for the 1642. I think the the Zambus casters are a good simple cost effective starting point, it the additional 2" of height is not an issue. If you want little height increase there are plans on the link for welding up the solution in the picture. It is a bit of work to install, drilling holes, aligning, etc. Of course if you do any heavy work you should relieve the weight from the casters with the adjustable standoffs.


img

Mustard Monster Site - Casters

Re: Lathe on casters

#4

PS: Don't make the threads-all standoffs so long!

Jerry Hall------WebKitFormBoundarya+xlLEfmA8pP6qz8

>

Re: Lathe on casters

#5

Re: Lathe on casters

john lucas

>I've had 2 lathes on casters over the years. It does work. I highly recommend what Jerry just posted. I've demoed on lathes with that set up and it works great. Much more solid than casters alone. I have a problem in that my lathe is too tall if I put anything under the feet. I believe I can set the casters up to give just 1/2" of clearance and still use that set up so that's in my plan of things to do.

Re: Lathe on casters

#6

Re: Lathe on casters

Ted Evans

>Many thanks to all for your input and suggestions, I tried to check each one out and make a decision. My first try is going to be with the locking casters, for two reasons, it seems to be the less expensive and also the quickest for me. Most of my turnings at this point are small, mostly pens and small bowls, up to about 8", so believe the stability problem may be manageable.

The lathe height may or may not present an issue. At present, it feels a little low for me however, 4" casters may be a little too much. If that proves to be the case, I will build a scab wooden floor around the lathe. It will not hurt my feelings to get my feet on a wooden floor rather than concrete.

Again, thanks to everyone for your comments.

Bear

Re: Lathe on casters

#7

John, this one is about 1/2 off the floor

Jerry Hall

>and the plans are on the Mustard site.


img

Re: Lathe on casters

#8

Re: John, this one is about 1/2 off the floor

john lucas

>Thanks for the photo Jerry. I kind of thought that it looked like that. I'm going to make a sketch right now so I won't forget and then I can start collecting the steel. I have a place locally that sells discount casters at good prices.

Re: Lathe on casters

#9

Dick Hines

Re: Lathe on casters

Dick Hines

>My club in Richmond has their PM 3520 on casters. It works great for me at 6'5" but we had to build a platform for the not so tall guys.

Re: Lathe on casters

#11

Re: Lathe on casters

Grant Wilkinson

>Ted

I use the machinery mover that Vega sells. When you're using the lathe, it's flat on the floor, not supported by the wheels at all. You move the lathe around with a wheeled handle that comes with the mover. It adds about 1/2" to the height of the lathe.

Re: Lathe on casters

#12

thanks- looks almost as good as my sketch :)

john lucas

>

Re: Lathe on casters

#13

Re: Lathe on casters

Kurt Bird

>Here are some photos of our club lathe, a Jet 1642 with the new Woodriver casters from Woodcraft. We built it with brick lintel angle iron, and made it 1" off the floor so the overall height wouldn't change much and it would roll OK on carpet.


img

Re: Lathe on casters

#14

Re: Lathe on casters 

Kurt Bird

>


img