Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Remedies for removing a stuck lid

Posts

Remedies for removing a stuck lid

#1

Remedies for removing a stuck lid

Paul Zerjay

>Short of prying off a stuck lid, does anyone know of a way to remove one? I have one that has really nowhere to grip, and has a finial that I would rather not break off either. TIA

Re: Remedies for removing a stuck lid

#2

Re: Remedies for removing a stuck lid

Russ Fairfield

>You have discovered the problem with making lids with a snap-fit.

Heat it in the oven at lowest setting, not to exceed 130F, which is at the point of being too hot to touch and hold with your fingers. If it is a stuck finish, the heat will soften it. If the wood is swollen from moisture, the heat should shrink it again. If there is a tight seal, the heated air inside may pop it as it expands.

If the wood has shrunk because it is too dry, put a pan of water in the oven with it for an hour.

One or the other will return it back to where it was when the lid fit.

Re: Remedies for removing a stuck lid

#3

Re: Remedies for removing a stuck lid

GalenV in Iowa

>Paul,

I've had two small boxes where the lids were stuck. I put them in the freezer for the day. When very cold I used the heat of my hand to warm the top faster than the bottom. The lids expanded and let loose of the box. It still took some force to pop it off but there was no other way I could think of to remove the top.

If your top fits inside a hollow form it may not work.

Galen

Re: Remedies for removing a stuck lid

#4

Re: Remedies for removing a stuck lid

john lucas

>If you have enough room to wrap an electrical wire around it you might be able to twist it off. use a wire that has a lot of friction. Wrap the wire around so you have 2 ends together. Grab these and twist. It will work similar to the way an oil filter wrench works. I've had great success with this on all sorts of things, especially getting stuck filters off of camera lenses.

Re: Remedies for removing a stuck lid

#5

Re: Remedies for removing a stuck lid

Barbara Gill, Remlik VA

>The time that happened to me I stuck it in the freezer for about an hour.

Re: Remedies for removing a stuck lid

#6

Pic of the piece

Paul Zerjay

>I put the piece in the freezer immediately after my original post, so we'll see what happens. If that doesn't work, I'm gonna try the oven method. do you think that the glue joints will be affected by the heat? Titebond


img

Re: Remedies for removing a stuck lid

#7

Wow! That's a beauty

Molly Winton

>

Re: Remedies for removing a stuck lid

#8

Freeze it

Jorge Castaneda~Downeast Maine

>Paul,

A while back I had a small box with same problem, our friend Joaz Hill sggested freezing it, and it did work. Give it a try.

Jorge

Re: Remedies for removing a stuck lid

#9

Woo Hoo

Paul Zerjay

>I had it in the freezer for about 1-1/2 hrs, pulled it out and still tighter than a well diggers you know what. So I immediately nuked it for 45 seconds on high, and with a little jostling, it came off. Thank you all for the replies.

Re: Remedies for removing a stuck lid

#10

Thanks Molly

Paul Zerjay

>

Re: Remedies for removing a stuck lid

#11

Re: Remedies for removing a stuck lid

Cyril Griesbach

>Beautiful piece, Paul.

Re: Remedies for removing a stuck lid

#12

Re: Woo Hoo

David Belser

>Congrats on getting it unstuck, as others have said it's a beautiful piece.

So now the question is how to make it not stick? I'm very curious as I have a 1 1/4" sphere box that is just a little too tight.

- Dave

Re: Remedies for removing a stuck lid

#13

Re: Woo Hoo

Jorge Castaneda~Downeast Maine

>David, try light sanding with 600 grit.

Re: Remedies for removing a stuck lid

#14

Ellis Walentine

Should have entered the "Elegant Forms" contest

Ellis Walentine

>That is a lovely composition, Paul. Congratulations. I'm glad you were able to get the lid off.

Cheers,

Ellis