Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Ferrule Question

Posts

Ferrule Question

#1

Ferrule Question

Bill Grumbine (Kutztown PA)

>Greetings all

For years I have been using copper plumbing fittings for the ferrules of my tools and gluing the steel into the socket in the wood. But, when it comes time for the tool to be replaced, I am faced with the option of also retiring a very pretty curly maple handle, which is the wood I favor for my tool handles. I have seen some people with tools sporting wood handles and ferrules that have a collar on them with a set screw. Is that something commercially available, or is it something people are making for themselves? Regardless, does anyone know where might I be able to obtain a few for my own use?

Thanks.

Re: Ferrule Question

#2

Re: Ferrule Question

mikevermont

>I was just browsing through the craft supplies catalog and saw a couple different inserts. They are both aluminum insterts with set screws. You can drill out your handle which will allow you to set the length of tool exposed depending on the use. I am planning on picking up a couple myself.

Re: Ferrule Question

#3

Re:I'm not sure why you don't just ....

Jamie Donaldson

>....knock out the old steel and replace with new in the familiar old handle? I usually grip the old steel in a vise and whack out the stub. There are tool holder inserts with set screws available for making handles, and I bought mine from Packard

Re: Ferrule Question

#4

LV

Bill Howatt

>Lee Valley sells Mike Hosaluk ferrules which are very nicely made. I bought one and also made one out of some large brass rod I had. Not an identical design but works.

Bill

Re: Ferrule Question

#5

Ditto what Jamie said. I just knock them out.

john lucas

>

Re: Ferrule Question

#6

Dick Hines

Re: LV

Dick Hines

>Bill, Myron Curtis in Va Beach used brass compression nuts. He turns the handle just large enough that the fitting is screwed onto the handle. If you want you can turn the brass to a smooth finish.

Re: Ferrule Question

#7

Re: Ferrule Question

Bill Grumbine (Kutztown PA)

>Thanks for all the responses and suggestions. I had thought about knocking the handle off the existing stub, but it never occurred to me to use a vise to hold the steel. I was thinking vise grips and arm strength, which is how I do a lot of things. Using a bench vise might make it easier.

Re: Ferrule Question

#8

i also do what jamie does

bob davis

>

Re: Ferrule Question

#9

Re: "A man without vise is like....

Jamie Donaldson

>... a sinking ship without freight to throw overboard!" Mark Twain

Re: Ferrule Question

#10

Re: Ferrule Question *LINK*

Stuart Johnson

>Oneway has some. I don't know how good they are or how they compare to others.


Thread-Lok� Tool Handle Ferrules

Re: Ferrule Question

#11

Re: Ferrule Question

john lucas

>Bill I use a vice. Clamp the blade in the vice. Then I get the biggest crescent wrench I have and tighten the jaw until they are barley loose on the steel. I grab the loose end of the wrench and then hit the bottom close to the steel with a deadblow hammer. Never takes more than a few hits to pop it off.

Re: Ferrule Question

#12

Re: "A man without vise is like....

Bill Grumbine (Kutztown PA)

>Jamie, is that vise or vice? ;-)

Re: Ferrule Question

#13

Galvanized pipe

Jorge Castaneda~Downeast Maine

>Bill,

when I made my first handle, there was a galvanized piece of pipe around, so I just cut what I needed and drilled holes and tap them for set screws. Not as pretty as copper, but a lot stronger and very cheap.

Works for me.

Jorge

Re: Ferrule Question

#14

Re:Whatever! (;-D)

Jamie Donaldson

>

Re: Ferrule Question

#15

Forgot

Jorge Castaneda~Downeast Maine

>to mention,

I cut the pipe with a hack saw and then put it on a chock, spin it and file it flat. Flip and repeat.

So you got you vise after all.

Re: Ferrule Question

#16

Re: Ferrule Question

Lan Brady

>Bill,

Al Basham (Cary NC) makes a great collet that works on wood handles.

http://www.albasham.com/catalog/

Lan

Re: Ferrule Question

#17

Steven Antonucci

A big guy like you should be able to knock em out?

steve antonucci

>I do, (me too)

Steve

Re: Ferrule Question

#18

Steven Antonucci

twist it first

steve antonucci

>CA glue had almost no shear strength. Twisting it breaks the connction, and I can often "wiggle" the handles off by hand. I use a bench vise with wooden jaws to avoid marking up my steel, and I've never had one I couldn't get with just my own hands...

S

Re: Ferrule Question

#20

Re: Ferrule Question

Bill Grumbine (Kutztown PA)

>Okay, the old tool is out and the new one is in. It actually went a lot easier than I expected. Maybe that is because lately everything I have been doing around here seems to take inordinate strength and effort to accomplish. But, I have a brandy new tool with a comfortable old handle. Thanks again for all the responses!

Re: Ferrule Question

#21

Re: Ferrule Question

Ed Heuslein

>Howdy Bill: Well, I see everybody does it a different way than I do. I also use copper 'cuz I think it looks nice. I drill a hole, tap it (copper and wood) and thread in a Threaded Insert - available at big box stores - 'till it's flush with the copper. Then screw in a allen-head set screw and you're ready to go. I find it takes very little pressure to hold in even the larger shanked tools.

Re: Ferrule Question

#22

Mike Stafford

Re: Ferrule Question *LINK*

Mike Stafford

>I buy ferrules just as you describe with a set screw from Frank Penta. He has them manufactured in several different sizes 1/4, 3/8, 1/2 and 5/8. They are all ever so slightly oversized to easily accommodate nominal dimensions. The great thing about them is that you can turn the sharp edge around and insert it into the handle for traveling to protect it. I have a complete set now for all my favorite tools and I love them.

A similar ferrule is sold by Craft Supplies and is marketed as the Hosaluk Handle Insert and is about $22. The link is below.


Hosaluk Handle Insert

Re: Ferrule Question

#23

Steve: you drill and thread your copper ferrules!-

adrien

>

Re: Ferrule Question

#24

Re: That's the dilemma of translating ....

Jamie Donaldson

>...the spoken word to tangible print!

Re: Ferrule Question

#25

I use them too...

Scott Burr in Ben Lomond CA

>I use them for awls/marking knifes and hand chisels. Lots of people on the handtool forum swear by them.