Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

outboard tool rest worthwhile?

Posts

outboard tool rest worthwhile?

#1

outboard tool rest worthwhile?

DizD

>I have an old (1954)Delta lathe I've recently put in service - mainly to do furniture parts. Would like to know if anyone who has used a freestanding outboard tool rest think this is worthwhile to consider. What are the pros and cons? Ebay has the Delta model from time to time. The option would be to carry pieces to someone with a larger lathe.

Re: outboard tool rest worthwhile?

#2

Re: outboard tool rest worthwhile?

Don Evans

>If this is the same lathe that I think it is, be sure and take into consideration that the outboard threads on the spindle are LEFT hand thread.

The original faceplates, if you have one, came with cross threads in them. In other words, you can put it on the inboard and outboard.

I've never used the type tool rest you are asking about so cannot address that as have no experience.

Don

Re: outboard tool rest worthwhile?

#3

Re: An outboard tool rest is a very .....

Jamie Donaldson

>...dangerous substitute for inboard swing capacity unless it is securely attached to the body of the lathe. They have a tendancy to lean into the spinning outboard work, and then all h#%%&)^$# breaks loose!

Re: outboard tool rest worthwhile?

#4

JL

Re: outboard tool rest worthwhile?

JL

>I've seen freestanding outboard tool rests used for bowls - but I don't recall ever seeing them used for furniture applications. I am curious as to what your application is.

Re: outboard tool rest worthwhile?

#5

Re: outboard tool rest worthwhile?

Ken Ward

>Unless this is something you would be using on a reg bases,I would find someone with a larger lathe,because as already said,unless you have a VERY secure setup it can be a dangerous setup.

Re: outboard tool rest worthwhile?

#6

Re: An outboard tool rest is a very .....

DizD

>Thanks. The arrangement doesn't look very forgiving - that's why I thought I'd better find out what to consider before trying something on my own.

Re: outboard tool rest worthwhile?

#7

Re: outboard tool rest worthwhile?

DizD

>I was thinking of small items like top for windsor stool, top for pedestal table - up to 14" or so.

Re: outboard tool rest worthwhile?

#8

Re: An outboard tool rest is a very .....

john lucas

>I've tried outboard tool rests. It requires a lot of experience to use successfully. As Jamie said it tries to pull the tool into the work and if the tool rest moves you get a pretty good catch. It also tends to vibrate easily.

Re: outboard tool rest worthwhile?

#9

Ellis Walentine

If it's substantial enough

Ellis Walentine

>Bill Grumbine welded the support arm for his outboard tool rest to the base of his old Poolewood lathe. That's probably the best way to have a secure rest that can't move relative to the lathe. Then there's the freestanding rest. A friend of mine has an antique Oliver floor-standing rest that is extremely heavy and stable. If you have enough mass and it contacts the floor positively, your odds of having a problem go down.

Ellis

Re: outboard tool rest worthwhile?

#10

Vicmarc outbaord tool rest *LINK*

john lucas

>They have the best system. It' fastened to the lathe so it doesn't go anywhere. Check out the one on the bottom of the page.


http://www.vicmarc.com/default.asp?contentID=545

Re: outboard tool rest worthwhile?

#11

Re: outboard tool rest worthwhile?

Peter Hyde

>Solution on an older Rockwell /Delta. Max diameter is 20" Uses a higher Oneway banjo. New stand top is 2 pieces 8/4 hard maple with 2 pcs 2x1/2" flat bar as ways.


img

Re: outboard tool rest worthwhile?

#12

This made my day!

DizD

>Thanks for sharing. With your concept and after looking at photos of outboard beds available, I'm already thinking of taking the board from under the lathe and replaceing it with some angelim I have, letting it extend out the left end to create base for a bed.

Re: outboard tool rest worthwhile?

#13

Made mine too!

Scott Burr in Ben Lomond CA

>Thanks Diz, I was going to ask the same question regarding my old Tomlee lathe.

Thanks!