Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

question about drilling...

Posts

question about drilling...

#1

question about drilling...

GaryG in MD

>I'm making a disc sander for my lathe out of an MDF disc. I'm going to screw a faceplate onto it. I want to know what size drill bit I should use for pilot holes. I know MDF is different from wood in this respect. Obviously I want to get the best possible purchase and longevity without doing any stupid damage. Should the pilot holes be smaller than the screw shaft size or should it be about the same size as the shaft, leaving only the threads on the outside of the hole? TIA, Gary

Re: question about drilling...

#2

Re: question about drilling...

Bill Crommett

>Whatever size you drill, be sure to put some CA glue into the holes before putting in the screws.

Re: question about drilling...

#3

Re: question about drilling...

Bruce McElhaney, Spring Lake, Michigan

>Pre-drilling the same size as the screw shank works good for most hardwoods, but I always drill smaller than the screw shank size for softwoods, MDF, plywood, etc.. Don't use traditional woodworking screws with thick or tapered shanks. Use speciality wood screws or sheet metal screws. I always use screws with course threads for MDF or plywood. Make sure the screws are as long as possible without going all the way through your MDF. Also be careful and make sure you don't over-tighten, or you could easily strip out MDF. Personally, I don't glue the screws in because it makes it to hard to remove them, but understand some folks do that for extra security.

Re: question about drilling...

#4

Re: question about drilling...

john lucas

>I try to use screws that have a larger thread and then drill for the shank size. Drywall screws work in a pinch, sheet metal screws will usually work if the thread is really large compared to the shank.

Re: question about drilling...

#5

Re: question about drilling...

Bruce McElhaney, Spring Lake, Michigan

>Others may disagree, but IMO, drywall screws are dangerous for this application. I would never use them even in a pinch. They may be OK for static loads, but in my experience they are too brittle and prone snapping off when under dynamic pressures.

Re: question about drilling...

#6

Re: question about drilling... *LINK*

GalenV in Iowa

>This may be of value to you.


MDF screws

Re: question about drilling...

#7

Re: Gary- make sure that the faceplate ....

Jamie Donaldson

>... holes are countersunk slightly on the MDF side, as screws tend to draw out a hump around the hole which prevents a flush fit. On a spinning surface this can prevent the disc from running true because the faceplate is not flat against the disc surface.

Re: question about drilling...

#8

this is why I love WoodCentral...

GaryG in MD

>Thanks, everyone, for your very concise, thoughtful, and on-the-money answers. All of you have given me important information that will give me a much higher probability of success. This is just what I needed to hear.

I'm using sheet-metal screws with a good ratio of threads to shank -- because they appear to be an appropriate choice and because I had them in my drawer. I already noted the "pyramiding" when I set all 4 screw points simultaneously through the faceplate holes to make sure I have perfect alignment before drilling.

On the business end, I'm using a thin, sticky-back interface pad with hooks (I soaked the MDF with shellac and got a nice firm surface for the sticky back), and I have a set of fuzzy-backed discs from 60 to 240.

I'll post the results after I give it a spin. ...Gary

Re: question about drilling...

#9

Re: question about drilling...

Barry Irby

>Gary, I made a MDF disc for my lathe and covered it with Neoprene as a vacuum chuck/face plate. Not exactly a sanding disk but similar. Mine is about 16" in diameter.

I drilled out the holes in the face plate to 1/4" diameter and used machine bolts (?) to hold the face plate on. These are the screws/bolts with counter sunk heads. I centered the face plate carefully and drilled through it, through the MDF. I countersunk the holes in the MDF to accept the heads of the bolts and lightly counter sunk the mating face to clean them up. I used those Cap Nuts on the face plate side to avoid having sharp edges. I glued/sealed everything with silicon just because it was a vacuum chuck. After the silicon cured I put it on the lathe and trued it up.

Two pieces of info here for you. I like the bolts. They are sturdy and I have no fear they will snap like drywall screws or pull out like some screws in MDF. AND, don't leave your sanding disk leaning against the side of a cabinet for a month or two. The shop gremlins left mine leaning and it warped. Beyond use, its a do over.

Re: question about drilling...

#10

thanks Barry...

GaryG in MD

>I appreciate your comments. If I were doing a 16" disc (!), I'd use bolts too! With a 6" disc, I'm comfortable that, if I do it right, the #10 sheet-metal screws should hold. This will be mod 1, anyway. Sorry to hear about your warp -- I'll be sure to store mine on a flat surface. ...Gary

Re: question about drilling...

#11

Re: thanks Barry...

Barry Irby

>Gary, Consider a larger disk. The biggest one your lathe will swing. Several advantages. A 9" disk has more than twice the surface area of a 6" one. More sand paper means longer life between changing the paper. Also, the rim speed is higher. I think you will find you do most of your sanding near the outer edge of the disk.

Whatever screws you use, be sure they are snug in the holes of the face plate. If you put a small screw in a large hole, the shaft is not supported and it may wobble back and forth and wallow out the hole in the MBF.

Re: question about drilling...

#12

Re: thanks Barry...

GaryG in MD

>More good points for my list.

The #10 screws I selected just fit the holes in my faceplate.

I have an investment in 6" sanding discs right now, but I'll certainly consider going to a larger disc after I get some practice with this one. I doubt that speed is going to be a problem -- at least not slow speed. My Jet 1236 doesn't go much below 800, so that's probably more than fast enough. On the other hand, your comment about working at the rim is well taken (linear speed decreases with the working radius). I've got the disc done, but now I have to build the table/rest. Thanks, Gary

Re: question about drilling...

#13

Re: Gary- here is the platform I made...

Jamie Donaldson

>...years ago to fit my old General. The MDF disc is 9" which seems to be a common sandpaper size.


img

Re: question about drilling...

#14

Re: thanks Barry...

Texian

>Here is another one w/ 15-3/4" disc and banjo-mounted platform. The platform angle is adjustable. Bought the sanding disc from local rental place that has floor sanders, for about half what it would have cost online.


img

Re: question about drilling...

#15

Re: Gary- here is the platform I made...

GaryG in MD

>Jamie, That's very simple and very practical -- just the way I like it. Great idea. Thanks, Gary

Re: question about drilling...

#16

Re: thanks Barry...

GaryG in MD

>That looks good too. Unfortunately, I don't do welding, so, for me, Jamie's is more practical. Thanks for the look, Gary