Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

controller for general 260 lathe

Posts

controller for general 260 lathe

#1

controller for general 260 lathe

bill gunn

>the controller on my General 260 variable speed with electronic controller seems to be broken. Can these be repaired? by whom? how can i definitively diagnose this proble .? General want big bucks for new one. Is there a source for rebuilt/reconditioned ones?

mant thanks

bill gunn

Re: controller for general 260 lathe

#2

Re: controller for general 260 lathe

John Veerkamp, Western Mo

>Most of the controllers are made by Baldor. Look for an authorized Baldor service shop. Most major cities have one. I had my controller for my DeltVS repaired. It cost me two hours labor. It lasted four years of regular use before dying again. A nes controller coule set you back $400 or more.

John

Re: controller for general 260 lathe

#3

Jesper, Denmark

Re: controller for general 260 lathe

Jesper, Denmark

>Depending on the age of your lathe, the controller is a Square D Altivar. These things are pretty cheap nowadays. Get the srial and model number from the old one and check with a local electrical supply house.

Keep the list of settings supplied with the old one. You will need them.

Re: controller for general 260 lathe

#4

Re: controller for general 260 lathe

Bill Crommett

>My controller died last year, and I tried to find a repair shop because General wanted $1300.00 for a new one. I hunted for a month trying to find an electronic guru to fix it. I found one who tried, but he said it needed a Mitsubishi something or other and he could not find a source for less than100 pieces. I settled for an aftermarket controller that cost me $250.00 and a good friend installed it for me. It works OK, but it doesn't have the torque the original equipment had.

We have a local Square - D factory here, but the chief of something told me that their division of Schnieder Electroniqe does not have the capability to repair that type of unit. If I had to do it over I would opt for a $500.00 unit instead, to give me more torque. Up-side: It has made me a gentler gouger.

Re: controller for general 260 lathe

#5

Re: controller for general 260 lathe

john lucas

>I'm not an electronic guru so take this with a grain of salt. I've installed 2 VFD's that were aftermarket. These things can be adjusted to achieve lots of levels of torque and different types of electronic braking. I would like to understand more about that. I did play with some of the settings but what you really need is someone who can read all the specs and set the adjustments for your motor and machine.

The reason these devices are so popular is that they can be set to optimize performance for a particular motor being used a particular way. An engineer who knows how to set these up could probably improve performance.

As you've noticed there are several brands on the market, Delta, and Altivar are the ones I've played with. Having grown up repairing odds and ends electronics I've watched it go from component repair to tossing the board and buying a new one. With these units either one is likely and repair takes someone with training on that device, at least to make it affordable.

Re: controller for general 260 lathe

#6

Re: controller for general 260 lathe *LINK*

Curly Smith

>I doubt that you'll find anybody that will economically fix your controller.

At the link you'll find 2 different drives for a 2HP motor that may work for your motor. Both are for 220v Single Phase in and 220v Three phase out.

The top drive is a variable torque drive and costs $200. The bottom drive is a constant torque drive and costs $300. I suggest you call them to talk about the differences between the drives and how those differences impact motor performance. You need to match the controller to both the motor and the intended use.

There are many places to buy controllers (another is Dealerselectric). I selected the link because it gives you easy access to the two distinct types of drives and motor performance info. As an example, the Constant Torque unit says

"High starting torque of 200% or greater at 1Hz

Newly developed technology - Intelligent Sensorless Vector Control - cope provides optimal high torque without motor tuning."

I don't know if that matches the performance of your old unit or not but the reps at either DrivesWarehouse or Dealerselectric will.


Variable Frequency AC Drives

Re: controller for general 260 lathe

#7

What's wrong with it?

GolfSteve in Calgary

>My industrial experience with small VSDs says:

1) If the thing does not work at all, open it up and look for a fuse. Sometimes you get lucky and there is an easily replaceable fuse, other times the fuse is soldered onto the circuit board. If this does not work, then the things are not repairable.

2) If the VSD turns on, lights flash, etc., but the drive acts funny (eg. no torque, stops/starts randomly, stutters, etc.), then the unit probably lost is programming settings and needs a new battery and needs to be reprogrammed. Sometimes there is a loose wire or a bad circuit board connection.

Cheers,