Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

More nubie motor pulley questions... *LINK*

Posts

More nubie motor pulley questions... *LINK*

#1

More nubie motor pulley questions... *LINK*

Scott Burr in Ben Lomond CA

>First off, thanks for all the great advise from my first post here. I'm learning a lot.

So I've been looking around and I can't find a exact match to the pulley I have on the lathe. I screwed up and found out that pulleys are measured on an O.D. not an I.D.

I've located 2 different sizes that could work with the Tomlee lathe, please see the attached link.

I'm thinking the smaller one listed (1-3/4 2-1/4 2-3/4 3-1/4") to get the lowest speeds possible (I'd buy 2 so they match).

The 2nd on down on the list could be good as well just a bit faster. The second pulley listed is very close to the one on the lathe now.

What you you all think? I know it only 1/4", but that could make a big difference.

Here's my original post:

http://www.woodcentral.com/cgi-bin/turning3.pl?read=212422

Thanks again for all your help!

Scott, a soon be turner... I hope.


Mc Master-Carr pulleys

Re: More nubie motor pulley questions... *LINK*

#2

Re: More nubie motor pulley questions...

Curly Smith

>None of those pulleys will give you what you want.

The governing formula is: rpm of motor pulley * diameter of motor pulley = rpm of equip pulley * diameter equip pulley

So, if you want a low-end speed of 400 RPM with a 1750 RPM motor then the large diameters that correspond to the two available small diameters are:

1750 RPM * 1.75" = 400 RPM * ?" ==> ? = 7.66"

1750 RPM * 2" = 400 RPM * ?" ==> ? = 8.75"

If you really need 400 RPM then you might want to consider either 5 or 6 groove step pulleys (similar to what you find on drill presses). As an example, the low speed on the 6-step Delta 15-231 drill press is 425 RPM while the 5-step 11-990 is 620 RPM. You can get some idea from here ToolPartsDirect on what's available but they don't list any info on the pulley, maybe they'd answer an email.

Your best bet is probably a visit to your local motor supply or electrical supply shop. However, before you spend too much money you might want to think about a cheap variable speed drive like Variable Speed Midi Lathe Conversion Kit . I don't know anything about the kit, I've just seen it advertised. Your local motor shop could probably also set you up with a variable speed motor and drive. The motor and control from a Craigslist treadmill would also probably work for your lathe.

Re: More nubie motor pulley questions... *LINK*

#3

Re: More nubie motor pulley questions...

wilbur

>It's true that using the outer diameter of a pulley won't be the most accurate way of calculating RPMs. What you need is the pitch diameter. That information should be readily available from any place selling pulleys that knows what they are doing, including McMaster-Carr. But the variance between outer diameter and pitch diameter won't really matter too much.

One other way to achieve a low RPM with pulleys is to put an intermediate pulley in between the motor pulley and the lathe pulley. This is called a jack shaft. It can be as simple as putting a 3" pulley on your 1725 RPM motor driving a 6" pulley on the jack shaft. This will cause the jack shaft to rotate at 862.5 RPM. Then set up a pair of step pulleys so that the ratio of the small step pulley on the jackshaft driving the large pulley on the lathe is 1:2.15. This will give you a final RPM at the lathe of 400 RPM.

But you don't have to be too precise here. If you get 385 RPM or 415 RPM, that's probably good enough. After all, the venerable Jet mini lathe, which also has a 10" swing like your lathe, has a low end speed of 500 RPM.

Re: More nubie motor pulley questions... *LINK*

#4

Boy are you right!

Scott Burr in Ben Lomond CA

>I'm back to square 1. I'll reverse engineer my drill press. I could get from 250-3000 rpm. I like the 250 not the 3K...

Re: More nubie motor pulley questions... *LINK*

#5

Thanks Wilbur...I need some serious help!

Scott Burr in Ben Lomond CA

>I about fried my brain trying to figure this out. I need a jack shaft, no doubt about it. I was hoping to reverse engineer my drill press witch is set up this way. I searched for a few hours online looking for a calculator and the the math equation to do this. No luck.

Can anybody help me out here?

Thanks

Re: More nubie motor pulley questions... *LINK*

#6

Re: Thanks Wilbur...I need some serious help! *LINK*

Curly Smith

>It's a series calculation.

First, run the calculation for the motor & motor pulley and the pulley on the jackshaft to calculate the jackshaft rpm. Then use the jackshaft rpm and your first step pulley diameter and the diameter of the step pulley on the headstock to calculate the headstock rpm.

Example:

motor is 1750 rpm, motor pulley is 2"

jackshaft pulley is 4"

step pulleys are both 2,3,4,5"

jackshaft rpm is then (motor rpm * motor pulley dia)/(jackshaft pulley dia) = (1750*2)/4 = 875 rpm

headstock rpm with belt in 2" and 5" steps (your lowest speed setting) is then (jackshaft rpm * jackshaft step dia)/(headstock step dia) = (875 rpm * 2)/(5) = 350 rpm (this would be the lowest possible speed)

the highest possible speed is then (875 rpm * 5)/2 = 2187 rpm

The above is based on a simple setup where you install a jackshaft on pillow blocks where the motor currently is. You attach the jackshaft pulley on one end and the step pulley on the other.


A simple pulley calculator