Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

What do you to finish your handles?

Posts

What do you to finish your handles?

#1

What do you to finish your handles?

Jim Stoppleworth

>Oil, wax, buffing only, lacquer, unfinished?

Just finished two handles for my Thompson bowl gouges. From Doug's site the instructions for handles say oil. I usually use Minwax wipe on poly. But I'm having a debate with myself this time. Handles are cherry and walnut. What do you or would you use?

Re: What do you to finish your handles?

#2

Re: What do you to finish your handles?

Charles Watson------WebKitFormBoundary+ATeQdvhmFc4

>waterlox has been my finish for most of my handles

Re: What do you to finish your handles?

#3

JL

Re: What do you to finish your handles?

JL

>Depends on the handle. For hammer handles and similar hand tools, I use oil/poly mix. For turning handles, I usually use just straight oil.

I have a friend who "suspends" his handles in oil for a couple of days and then takes them out for a couple of weeks to cure. Don't know if I would go that route though.

Re: What do you to finish your handles?

#4

Re: What do you to finish your handles?

Bill Neddow------WebKitFormBoundary+w+uCg3oRve3I+f

>I generally use an oil -- and I only sand the handles to 80 grit because I want to have some "grip" on the handle when it is dry.

Re: What do you to finish your handles?

#5

Re: What do you to finish your handles?

john lucas

>I use my tool handles for both finish testing and sometimes finishing techniques such as dyes, wax application, painting etc. I might try different finishes to see how they work and hold up. I would say most of the time I just lacquer since that's the technique I use for my hand mirrors.

Re: What do you to finish your handles?

#6

Re: What do you to finish your handles?

Joe Herrmann

>I just finished making some handles for some of my new Thompson tools as well. I used Bush oil initially (I bought some at Saratoga Springs but usually use BLO) and then spray Deft that was rubbed out with 4/0 steel wool. I think this treatment works good and is what I use on most work, both turned and flat. However, depending on how large the work is, I might opt for brushed on poly instead.

Joe

Re: What do you to finish your handles?

#7

Re: I haven't used anything....

Donna Banfield

>I've turned about a half-dozen handles, and I've never put any finish on them. I sand up to 320, and then burnish it with the chips/shavings.

So, what am I missing? And why might I want a finish on the handles?

Re: What do you to finish your handles?

#8

Re: I haven't used anything....

Jim Stoppleworth

>I'm thinking along those same lines for the cherry handle. I don't think there is an ironclad reason to put finish on a working handle.

I guess since our tools that we purchase handled are almost always finished we get in that mindset for the ones we turn.

Re: What do you to finish your handles?

#9

Steven Antonucci

I've been known to use my birdseye maple handles

steve antonucci

>as hammers and worse! I used to spray them with lacquer, which I still do hit and miss if I think of it.

Otherwise, my handle get human oiled over a great many years. Sanded if I had a bad day with the skew with whatever is laying around ALONG THE GRAIN ONLY with the tool off the lathe.

I've probably done 100 or so by now...

S

Re: What do you to finish your handles?

#10

Nothing

Scott Hurley in N VA

>I also sand to only 80 or 100 grit, and don't put anything on the handles. Over time, the oil in your hands will give them a nice patina. I've also been known to sand off the finish on pre-finished handles - gives me better grip.

Scott

Re: What do you to finish your handles?

#11

I make 1/4" round skews and ...

Ed Moore of SW VA

>handles with a 1/4" collet for sale. I used to just spray with a good lacquer, but decided I wanted a more durable finish. I just finished twenty cherry collet handles with a coat of General Seal-A-Cell and a two coats of Arm-R-Seal. I am VERY pleased with the results. I want my handles to look as good as possible.

Why a 1/4" collet handle? I take an 8" HSS round 1/4" rod and grind a skew on one end and a point tool on the other (three-face tool). I plan to make three 1/4" tools with HSS cutters CA'd into them. One will be straight, one will have a shallow swan-neck and the other a more pronounced swan-neck. The latter should be good for hollowing globe ornaments. This will complete a set consisting of one collet handle, one 5/32" Tee Allen wrench, and four 1/4" tools.

Note: 5/32" is VERY close to 4 mm. The blue Oneway Tee Allen wrench also works with the collets, and vice versa.

Ed

Re: What do you to finish your handles?

#12

Maybe this picture will help explain ...

Ed Moore of SW VA

>what I was talking about. After posting the note I zipped up to the shop with the camera, grabbed a piece of plywood and what I wanted to show. The small oak pieces are simple caps for the 1/4" round skew. The skews are SHARP and the caps prevent unintended cuts. DAMHIKT The three tools with HSS inserts mentioned above aren't made yet.

Ed


img

Re: What do you to finish your handles?

#13

Re: What do you to finish your handles?

Mike Brazeau

>I like nice looking handles and generally use some oil or danish oil to pop the grain and then a few applications of Myland's Quickbuild. Seem to hold up fine and look good. I also like to use the ferrules from Lee Valley. For a buck they add a nice touch. Osage is my favorite wood for handles. Love that smooth feel when you grip it.


img