Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Loc-Tite Loosening?

Posts

Loc-Tite Loosening?

#1

Loc-Tite Loosening?

charlie belden

>I have the JET VS mini/midi which required an adapter on the head stock end to accomodate the SuperNova2 chucks. Adapter would sometimes unscrew when I stopped the turninbg rather than let it spin down to a stop.

SO - after the last episode, which spun the lip of a hollow form into the tool rest - I LocTited that sucker (Blue LocTite). Hasn't come loose since.

But now I want to use the face plate that came with the lathe - which meant removing the adapter. WRONG! Bent my knock out bar trying to get it off.

HELP - need the Secret Method for unLocing LocTite - and please don't suggest heating things to 400 to 600 degrees F. . .

Other possibility is to buy another faceplate - with the diameter and thread matching the adapter. Sources?

(Every solution seems to create a new problem)

Re: Loc-Tite Loosening?

#2

Re: Loc-Tite Loosening?

R Payne

>If you used loctite brand then check

http://www.loctiteproducts.com/questions.asp?answerme=125

ron

Re: Loc-Tite Loosening?

#3

Re: Loc-Tite Loosening?

charlie belden

>OK - so BLUE LocTite can be removed "using hand tools"

The JET VS mini/midi does not have a spindle lock. There's a hole in the head stock shaft for a Tommy Bar - which didn't come with the unit. And using the Knock Out Bar merely bent it - so now it doesn't work as a knock out bar.

The hole diameter isn't that large - and the distance to the ways, to use it as a stop, is about 9" - a nice long arm to bend it with.

I know before open end wrenches, box wrenches and crescent wrenches "spanners" were used - and a spanner with a pin to go in the hole would be nice to have - but I have no idea where to find one that'd work for this application.

Re: Loc-Tite Loosening?

#4

Re: Loc-Tite Loosening?

Carole Valentine

>Your post confuses me, which is not unusual. I have a Jet Mini and Supernove2 chucks, but the adapter screws into the chuck body and is locked there with a grub screw. Then the whole works is screwed onto the lathe spindle. In other words, the adapter stays with the chuck, not on the spindle. It really does not make sense for a chuck adapter to be fixed to the lathe spindle. Am I misreading something?

Re: Loc-Tite Loosening?

#5

Spindle adapter vs. chuck insert

Doc Green

>Carole, there are two different items involved here. A spindle adapter screws onto the headstock spindle to change its thread size and it stays with the spindle. I have one on my PM to change 1 1/4 threads down to 1" threads.

On the other hand, a chuck insert is a threaded part that fits into a chuck to "customize" it to whatever thread is on the spindle. It stays with the chuck, of course. ~Doc

Re: Loc-Tite Loosening?

#7

Re: Spindle adapter vs. chuck insert

don lewonczyk

>I don't suppose you have a impact gun with a deep well socket big enough to fit over the adaptor, do you? That would work without to much effort to hold the spindle from turning. DonL

Re: Loc-Tite Loosening?

#8

Re: Spindle adapter vs. chuck insert

Mike Gould

>Charlie,

I use alot of Loctite threadlockers. Mostly the Red but also the Blue for small screws.

The Blue usually breaks free with moderate tourqe on the drivers. The Red needs heat.

I would try to heat the sdapter with a propane torch. Not enough to get the headstock hot...just enough to get the Loctite to release. It should only take a few second of heat.

Good Luck,

---Mike Gould---

Re: Loc-Tite Loosening?

#9

Re: Places to buy a spanner wrench

john lucas

>I've bought mine from MSC and www.use-enco.com That is what you need. I think that's also a better tool for locking the Jet mini spindle than the long bars they give you.

Re: Loc-Tite Loosening?

#10

Re: HEAT works every time

Russ Fairfield

>Doesn't take a lot.

Re: Loc-Tite Loosening?

#11

Re: HEAT works every time

Bill Turpin in WNC mountains

>Take a healthy sized soldering iron (suggest Weller trigger/gun type 250 watt) and heat the screw with the iron tip. You should be able to heat the threads enough without over-heating the bearings.

Re: Loc-Tite Loosening?

#12

Re: Loc-Tite Loosening?

GalenV in Iowa

>I would say the spanner wrench would give you a better hold but to get by if you have the chain jaw vice-grips and put a rubbe pad under it would give you a good hold. I've used a rubber lined strap oil wrench but in this case you do not have enough width.

If you apply heat to the outer surface of the adapter and then break it's bond and remove the adapter fast you can keep the heat from conducting on to the spindle and then into bearings.

Oh if you are like me be sure you are turning things the right direction!

Galen

You may have to buy a new lathe to do other projects! :>)

Re: Loc-Tite Loosening?

#13

Re: HEAT works every time

charlie belden

>I'm standing mid shin deep in shavings, mostly dry shavings, with 2+ inches more on the lathe bench, next to a full wood rack - and you want me to do WHAT with fire?!

Actually, I've got one of those heat guns - the kind that'll char wood - and raise a nasty blister on skin - that probably would have worked on loosening the LocTite.

Came up with a simpler solution - very odd behavior for me. Shortened the bending moment arm of the knock out bar I'd used to hold the headstock fixed by putting a block of wood under it - close to the headstock. Didn't need a cheater bar since I somehow had acquired - not sure when or how - an 18" crescent wrench that'll open to 2 1/4". Some moderate force, applied gradaully and things started moving, albeit slowly. And for once I was patient - another behavioral anomaly - and took it slow and easy. Worked!

The adapter in question takes the thread on the head stock up from whatever it is stock on the JET mini/midi to whatever the diameter is on the SuperNova2 chuckS. You see, I have two SN2 chucks - and rather than leave one in each chuck, I leave the adapter on the drive spindle of the lathe. May be a Penny Wise, Pound Foolish thing, but up 'til now I haven't been using the stock face plate. And perhaps at some point in the future I'll get a bigger lathe that the SN2s will fit on without an adapter - so there'll be no LocTite-ing anything in the SN2 chucks.

Anyway - thanks to all who provided suggestions.

Re: Loc-Tite Loosening?

#14

Re: HEAT works every time

Carole Valentine

>The SN2 chucks ALL require an adapter except for the M33 direct threaded model. So even if you get a bigger lathe, you will still need adapters. (Unless you get a Oneway and decide to buy all new direct threaded chucks) :)) "Penny wise, pound foolish"...you said it, not me!