Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Departure From Round and Brown

Posts

Departure From Round and Brown

#1

Departure From Round and Brown

charlie belden

>Using 3 centers on each end of a blank and turning arcs, you can do three sided stuff. And if you rotate the centers on one end a quarter turn you can add a twist. With an eccentric chuck you can turn some pretty odd things as well. Then there's the eccentric hemispheres / plates.

But what about if the surface you turn a hemisphere into were basically two wedges - flat on the back but in opposing directions on the face to be turned? The angled "step" at their interface would break up the look of the hemispherical concavity, introducing a degree of confusion due to the ambiguity of what you're seeing. Looking straight down in the attached example you'd see a round red spot. But tilt and 'or rotate the piece and "round" breaks up .

I'm certain this isn't something new - too many turners trying so many different things for so long. But it does have a lot of possibilities for at least getting past the "round" of Brown & Round. Vary the depth of the hemisphere, the location of its center relative to the two wedges interface, three wedges, . . .

Anyone have actual examples they've done or links to pieces that use this idea?


img

Re: Departure From Round and Brown

#2

Re: Departure From Round and Brown

Peter Rand

>Charlie - have a look at Stephen Hogbin's work at

http://www.makersgallery.com/hogbin/

long ago he make the "walking bowl" a seminal piece in deconstruction woodturning

which is based on what I think you are thinking of here - he still riffs on this theme

deconstruction rocks

Re: Departure From Round and Brown

#3

Steven Antonucci

Why force something like this on the lathe?

steve antonucci

>Scratching my head here Chalie? If I assume that the lathe is a tool for making round things, why would I want to use it in some contorted way to get opposing wedges? I think I could work this out in 5 minutes using a jointer and a drill press?

I know that you can turn a cube as an academic exercise, but I can make one with other tools much easier, so I would probably opt for square peg, square hole...

S

Re: Departure From Round and Brown

#4

Re: Why force something like this on the lathe?

charlie belden

>Steve:

I'm not sure if you've got your tongue planted firmly in your cheek or if my illustration and explanation was that unclear.

The idea I had in mind was turning a hemisphere into the faceS of a blank with two sloping top faces in one solid piece of wood.

Using a drill press, you'd get vertical walls of a hole rather than hemispherical surfaces, albeit partial ones.

Peter:

This is not a hemisphere turned into the flat face of a piece of wood then cut up and the pieces reassembled at an angle to one another. One piece of wood with two opposing slanted surface on the "top" into which a hemispherical concavity is turned.

The sloping faces can be done with a bench plane and some careful chiseling for the vertical faces.

The attached 3 views may (or maynot) clarify things.


img

Re: Departure From Round and Brown

#5

Re: Why force something like this on the lathe?

Bill Neddow------WebKitFormBoundary+w+uCg3oRve3I+f

>Very interesting concept, Charlie. Certainly worth some experiments.

Re: Departure From Round and Brown

#6

Re: Departure From Round and Brown

Chip in Plano

>Blaze a trail with your concept. I got it with the 1st illustration. Do a series and throw in a little decontruction after turning the center for variety. I'm waiting for a prototype.

Re: Departure From Round and Brown

#7

Steven Antonucci

I was mostly serious...

steve antonucci

>I understood what you meant, and in revisiting it, I think it's somewhat simple to do.

Assuming that the order of operations doesn't effect the output, You could grind a spade bit to your semicircle and drill it as I described. Perhaps even an easier way would be to mount the flat blank, then turn the semicircle. Once that was done, a few careful passes over the jointer bed to add the tapers and you are done.

My point was that I thought you wanted to do every operation using only the lathe, and milling two opposing wedges seems to be better suited using other means.

Steve

Re: Departure From Round and Brown

#8

Re: I was mostly serious...

charlie belden

>Steve:

I guess including a scale would've helped. The circle I had in mind would be 5 to 6" in say an 8x8 blank about 1 1/2" to 2" thick. IF there were a spade bid 5-6" acrossed, I wouldn't chuck it up in a drill press and try and use it. One incident with a forstner bit that caught in internal knot - in a piece that was in a clamped down vise - gave me a healthy respect for drill presses.

But you're right about the order of operations. It's easier to turn a hemisphere into a FLAT piece THEN cut the tapers - than it is to start with the tapered blank and turn into it.

Rather than a joiner to do the tapers I'm thinking a bandsaw would be a lot faster. Both would probably require some chiseling on the newly created vertical faces.

I seem to start out with the hardest way of doing things - then - thanks to feedback from others head off in an easier direction.

The visual ambiguity of this idea is what I find interesting. As you change your persepective, new relationships appear. The visual ambiguity could be increased with some thought out texturing, pyrography or Priddle's Wood Vaporization. Simpler yet, use color - a different color on each of the faces. As your perspective changes some colored faces would disappear when viewed "on end".

Re: Departure From Round and Brown

#9

Steven Antonucci

Color shifting automotive paint

steve antonucci

>If you really want to mess with someone, use color shifting paint like they use on cars.

I remember standing in a parking lot in 1997 with a guy who kept telling me to check out the awesome green Mustang. For the life of me, I had no idea what the H*&*^^ he was talking about, since there was only a purple one. He was standing on one side, I was on the other, and as soon as he pointed to it, I accused him of being color blind.

As we moved, the car changed colors before our eyes. Decidedly, one of the coolest things I had ever seen. Several laps around the car later, we went into the diner to grab breakfast...

Steve