Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Motor upgrade for Delta Bandsaw

Posts

Motor upgrade for Delta Bandsaw

#1

Motor upgrade for Delta Bandsaw

Steve In NC

>Hi folks

I have a 30 year old Delta 14" bandsaw. It has done me well for many years of flat work. I just added a riser block so I could rough bowl blanks.

Been using it for a couple of weeks and it appears to be underpowered when cutting 8-10 inch thick blanks (motor boggs down and I have to stop before it burns up. I am using a 3/8 x 3 tpi blade.

It currently hase a 3/4 HP motor. I have a 1.5 HP sitting in the shop that will fit. Any downside of doubling the HP.

Steve

Re: Motor upgrade for Delta Bandsaw

#2

Re:Should be no real problem.....

Jamie Donaldson

>.. if everything can be made to fit. Just don't overdo the blade tensioning and crack the frame.

Re: Motor upgrade for Delta Bandsaw

#3

Re:Should be no real problem.....

Ken ward

>That should work great.I rebuilt an old Walker turner and raised it to 13" resaw.I bought a 1 1/2 hp ,but it runs backwords,but I found a shop where there going to reverse it for me.

Re: Motor upgrade for Delta Bandsaw

#4

Keith Tompkins

Re: Motor upgrade for Delta Bandsaw

Keith Tompkins

>Hi Steve, the only down side is that my 2HP motor dims the shop lights when starting up, wired for 120 volts. Switching the motor to run on 220 will cure that. The motor swap is definately the way to go....my old motor hung under the saw, the new one sits on shopmade mounts down in the base.

Re: Motor upgrade for Delta Bandsaw

#5

Re: Motor upgrade for Delta Bandsaw

Russ Fairfield

>No problems at all. I have one about the same age with an open stand and a 2hp motor. I had to make an extension out of plywood for the larger motor, and the guard would no longer fit. It made the saw come alive.

Re: Motor upgrade for Delta Bandsaw

#6

Dominic in Bucks County PA

It'll work!

Dominic in Bucks County PA

>I did something similar when I dropped a 2HP motor into my Jet 14" bandsaw. I documented the project here:

JET BANDSAW UPGRADES

I guess the only thing to be careful of is that the shaft size on the new motor may be different from the old motor. That may mean you need new pulleys. Be sure to maintain the same diameter. In my case I couldn't and needed to get a new driver pulley (on the motor) as well as a driven pulley (on the BS). I needed to make sure that the ratio between their two diameters was the same as the ration between the existing driven and driver pulley so that the speed of the BS would remain the same. I ordered my pulleys through Grainger.

One other tip, use link belt! That made a HUGE difference in the smoothnesss of operation of the BS.

See ya around,

Dominic

Re: Motor upgrade for Delta Bandsaw

#7

Re: Thanks all

Steve in NC

>Thanks for the feed back. Looks like just a few minor modifications and I should be good to go.

Steve

Re: Motor upgrade for Delta Bandsaw

#8

One more thing or maybe two.....

Barry Irby

>Make sure the motor's speed is the same as the old one. My Delta BS has a 1725 RPM motor and I have another that is 2hp, but runs twice as fast. I would have to change the pulleys to get the speed back down.

And, be sure the wiring and switch are suitable for the new larger motor. I would have to change my switch also.

Check out Louis Itura's catalog. He suggests increasing the speed of the blade. He is a wealth of information.

Re: Motor upgrade for Delta Bandsaw

#9

Re: Motor upgrade for Delta Bandsaw

rick pixley

>I attended a club sponsored demo with Trent Bosch a few years back.He mentioned the only bandsaw he used was an old delta 14 in,with a 3hp motor no less...