Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Combo Salt & Pepper shaker

Posts

Combo Salt & Pepper shaker

#1

Combo Salt & Pepper shaker

WayneLeach - NW Ont

>Hi Everyone,

This combo salt and pepper shaker/grinder started out as a prototype and made from scrap poplar and ?

My wife wanted something to replace the old worn out one she had for many years.

I used the short crushgrind mechanism and in the top where the salt reservoir is, I epoxied in brass plumbing fittings ( I need John Lucas to teach me how to cut threads in wood LOL)

It turned out so good that she won't part with it, so I finished it and now it is in service.

I had made inqiries about mechanisms to make combo units before but there was no information available and I was stymied until I got the crushgrind unit. Works great!

The cap is made from an unknown wood from southern Georgia. I thought it was cherry but NO typical cherry smell. The bark looked similar to cherry.

Comments/critiques always welcome.

Wayne


img

Re: Combo Salt & Pepper shaker

#2

Re: Combo Salt & Pepper shaker-detail 

WayneLeach - NW Ont

>


img

Re: Combo Salt & Pepper shaker

#3

Re: Combo Salt & Pepper shaker-detail

Don Orr

>Now that right there is one great idea. I can see that being copied all over the place. Nice job !

Re: Combo Salt & Pepper shaker

#4

Re: Combo Salt & Pepper shaker

Mike Brazeau

>Great idea and nice design and workmanship Wayne. I am going to clip for future consideration and also send on to a fellow in our guild that has been doing some neat things with the crush grind. I think I would have been inclined to use a PVC fitting rather than brass though, assuming it is salt at the top? Maybe I am misreading?

Re: Combo Salt & Pepper shaker

#5

Re: Combo Salt & Pepper shaker

Cyril Griesbach

>Very nice, Wayne. A guy in our club made one a few months back. I'm not sure what kind of grind mech he used but as a machinist he did make some of the salt shaker parts himself.

Re: Combo Salt & Pepper shaker

#6

Ellis Walentine

I love the idea

Ellis Walentine

>If I understand how it works, the peppercorns go into the center chamber of the upper part of the base, the salt is all contained in the cap, and the threaded fitting is to keep the lid from falling off when you turn it upside down to shake out some salt. If so, where is the plug for the salt chamber, or do you use a cork in the end of the pipe nipple?

Ellis

Re: Combo Salt & Pepper shaker

#7

Re: Mike you are right!

WayneLeach - NW Ont

>Mike,

As I said in the write up, it was a prototype and I only had a brass fitting. If I make more I would DEFINITELY use plastic of some sort for corrosion reasons. I will be interested to see if the salt dose anything to the brass over time?

Thanks for the input,

Best regards,

Wayne

Re: Combo Salt & Pepper shaker

#8

Re: I love the idea

WayneLeach - NW Ont

>Hi Ellis,

The peppercorns go into the bottom or lower portion of the shaker as the mechanism is less than 3" long/high!

The salt is contained in a 1"?? bored hole where the female threaded fitting is and the cap threads off to add more salt.

Clear as mud?

I can maybe add a photo if you like. Thanks for the interest, its a neat project and lots of friends already want one.

Next time I will use something more exotic than poplar!

Wayne

Re: Combo Salt & Pepper shaker

#9

Ellis Walentine

Still confused

Ellis Walentine

>I've made crush grind mills before, and the grinder takes up the entire inside of the bottom section, right? So I'm thinking the peppercorns have to go into the upper part of the mill, above the mechanism, but it sounds like you're putting the salt in there too.

Sorry to be slow on the uptake, but I think I need to see a section drawing.

Ellis

Re: Combo Salt & Pepper shaker

#10

Re: Still confused

WayneLeach - NW Ont

>Ellis,

I will sketch something and show what I did tonight, so check back later tonight.

Wayne

Re: Combo Salt & Pepper shaker

#11

Re: Still confused

WayneLeach - NW Ont

>Ellis,

With the short mill the peppercorns are confined to the mill housing itself which is located in the bottom of the sshaker. The second part of the shaker has a hole in bottom about 1" deep to fit the mill and the top of it has approx. 1-1/8" hole about 2" deep to hold the salt-this leaves a 1/4" partition to keep the peppercorns out.

I am including a sketch which should clear things up.

Hope this helps, let me know if I can be more helpfull?

Wayne


img

Re: Combo Salt & Pepper shaker

#12

How do you?

Jorge Castaneda~Downeast Maine

>Wayne,

How do you get pepper or salt as needed, or you get both all the time?,

I am still confused too.

Thanks

Jorge

Re: Combo Salt & Pepper shaker

#13

Re: Still confused

bob henry

>I can't make out the measurement for the height of the top section?

Bob

Re: Combo Salt & Pepper shaker

#14

Re: Still confused

Wayne Leach - NW Ontario

>Bob,

Its about 1-1/2" but its not critical. Depends on what look you want.

Thanks for the interest.

Wayne

Re: Combo Salt & Pepper shaker

#15

Re: How do you?

Wayne Leach - NW Ontario

>Jorge,

The table salt is contained in a seperate compartment above the mill and shaken out of 8 holes in the top/cap like a regular salt shaker. The pepper is ground and dispensed out the bottom like any grinder.

If you want more clear info I can take more pics and do a better drawing and send to you in .pdf format by email?

Please let me know.

Wayne

Re: Combo Salt & Pepper shaker

#16

Thanks Wayne,

Jorge Castaneda~Downeast Maine

>It is all clear now,

I should wipe my glasses more often...