Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

A loud bang and I was walking toward the light...

Posts

A loud bang and I was walking toward the light...

#1

Steven Antonucci

A loud bang and I was walking toward the light...

steve antonucci

>to shut the dang thing off!

I had decided to make a large natural edge cherry lamp shade. Third time I've tried, and I am 0 for 3. First one ended up as a small djembe. Second one is a large bowl that I am not very fond of.

This one started off pretty nicely, until I got a catch removing the center cone and blew up my natural edge whilst also slammin' up the back of my right hand. So, I went for a large translucent bowl. It was 1/8" all the way down, as measured by the 100w light bulb I was using to gauge wall thickness. One small nib at the bottom to get and I was done.

I had been working on it all day, and I suspect that I had remove 49.5 pounds from a 50# log. The lathe was running at 1000RPM and I was tired, so I didn't think to slow it down. One last cut...

What actually happened is still subject to debate. One second, there was a large translucent end grain cherry bowl in front of me, and the next minute, I was staring at a 100W light bulb. No hint of a bowl at all. Apparently 1/8" of wood isn't enough to hold a bowl if you get a minor catch when cleaning up the inside of the bowl with a scraper.

Will I try it again? Probably. Will I push 3/32" next time? Why not? If I'm going to die, I going to die trying...

steve

Re: A loud bang and I was walking toward the light...

#2

Steve Kubien

Re: A loud bang and I was walking toward the light

Steve Kubien

>On of my common thoughts as I enter the floor of the dojo is, "It's a good day to die." Might as well have fun while you're doing it!

Steve

Re: A loud bang and I was walking toward the light...

#3

Re: A loud bang and I was walking toward the light

john lucas

>Steve Thanks for the laugh. I think we've all been there. Glad you weren't hurt. Maybe instead of saying "hey bubba watch this". We woodturners should say " I think I'll just take one last cut"

Re: A loud bang and I was walking toward the light...

#4

Re: A loud bang and I was walking toward the light

Frank Joseph

>Steve you will try again and again,

Re: A loud bang and I was walking toward the light...

#5

...just one last cut...

Thad

>...for me, it's "Heck, I can reach that w/o moving the tool rest."

Sorry for your loss Steve...(but glad it wasn't the pear)

:)

~ Thad

Re: A loud bang and I was walking toward the light...

#6

Re: A loud bang and I was walking toward the light

Jerry McCaffrey

>Steve...can you find most of the pieces? A little CA, a little Bondo, a little paint and Bob's Your Uncle.

Jerry

Re: A loud bang and I was walking toward the light...

#7

Steven Antonucci

All the kings horses, and all the kings men...

steve antonucci

>

Re: A loud bang and I was walking toward the light...

#8

Brad Vietje

Re: A loud bang and I was walking toward the light

Brad Vietje

>Steve,

Glad you were not hurt.

I'm sure you'll have success one of these times. Maybe you can locate a Peter Bloch video to make your learning curve a little easier. I think you can buy a CD of his lampshade presentation from the Guild of New Hampshire Woodworkers: (www.gnhw.org)

Cherry, BTW, isn't a very translucent wood. I've made a few small shades from Red Maple and White Birch, and two larger ones from Aspen -- and I think Aspen is the way to go. Having made a large number of natural edge cherry bowls, I no longer bother keeping the bark on for really thin edges -- probably 3/8 and up for me. Black Cherry bark seems so rough and varied that it becomes too difficult to be worth it for thinner work, where other species would be fine. I have wanted to try a natural edge Red Oak shade though....

Safe spinning,

Brad Vietje

Newbury, VT

Re: A loud bang and I was walking toward the light...

#9

Steven Antonucci

Cherry at 1/8" is pretty tranlucent :-)

steve antonucci

>Peter is of course the matser, but I saw Andre Martel do it in about 1 hr in a demo with a hook tool start to finish (almost).

I need to pick up my game...

S


img

Re: A loud bang and I was walking toward the light...

#10

Steven Antonucci

Where I left off... 

steve antonucci

>


img

Re: A loud bang and I was walking toward the light...

#11

Brad Vietje

Re: Where I left off...

Brad Vietje

>Gosh Steve, you did get pretty close!

I'd be interested to see the wood when it dries out. In my experience, fruit woods are pretty translucent when wet (especially the sap wood), but far less so when dry.

I roomed with Andre Martel three years ago at the Pinkerton symposium, and we both stayed at Peter Bloch's house this May. He's a real nice guy, in addition to his excellent tools and turnings. I made two small shades with the Martel Hook Tool, and the Aspen ones were roughed with the hook tool, but finished with the Sorby Hooker Tool (teardrop scraper).

One day I'll grab a fresh Red Oak log and make a shade and see how it goes. I like the way the light comes through the pores on the end grain of small pieces, so I'm hoping a larger lamp shade will look nice. I hope well before then you have some nice looking (one piece) shades to post here!

Safe spinning,

Brad Vietje

Newbury, VT