Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Help -- stuck Morse taper adapter

Posts

Help -- stuck Morse taper adapter

#1

Help -- stuck Morse taper adapter

wilbur

>My Conover lathe has a #3 Morse taper in the headstock. Almost all of my accessories are #2 MT. No problem -- I'll just pick up a #3 MT to #2 MT adapter, which works great.

Except that the last time I used it, my drive center got really stuck in the adapter. There's a slot in the end of the adapter, which you can see in the picture, that seems to be there to help get the #2 MT accessory out.


I've done everything short of sticking a screwdriver or something in the slot and banging on the end of the stuck drive center with a really big hammer, which I don't really want to do in case I damage the end of my drive center form the pounding.

I think that there's some easy way to take advantage of this slot that I'm just missing. Any suggestions?

Re: Help -- stuck Morse taper adapter

#2

You're Close

Mark Mandell - Gone Round In Jersey

>The slot is to drive in a steel wedge called a drift key to pop the MT accessory out. Same thing is done to knock loose the quill in a drill press. You should have gotten that wedge along with the adapter.

Re: Help -- stuck Morse taper adapter

#3

Re: You're Close

john lucas

>Mark is dead on. The adaptors don't usually come with the drift. Your drill press might have. If you don't have one stick a couple of screwdriver in the hole. The idea is to drive a wedge in the slot so rig up the screwdrivers so one of them is like a wedge and tap it with a mallet. You might want to order a drift punch. You can get them from any machinist supply house like Enco, MSC, Travers, or maybe even from DElta or Jet if you look for parts for the drill press.

Re: Help -- stuck Morse taper adapter

#4

Re: You're Close

wilbur

>Thanks, Mark -- that was quick!

After Googling drift key, it seems that there are drift keys for each Morse taper. Would I use the #2 MT drift key, since the thing that's stick has a #2 Morse taper, or a #3 MT drift key, since the adapter has a #3 MT?

Re: Help -- stuck Morse taper adapter

#5

Re: Help -- stuck Morse taper adapter

Jake Niedling

>I have the same lathe. What I usually do, is hold on to the top of the #3 and tap it hard on the side with a hardwood dowel. Keep hitting it harder and the #2 will usually just drop out. Hold it so the #2 is pointing down.

Re: Help -- stuck Morse taper adapter

#6

Re: Help -- stuck Morse taper adapter

john lucas

>I just put a #2 morse taper in my #3 adaptor and the drift punch that removes it has a #2 stamped on it. The larger drift I have is too wide to fit in the slot. It has a #3 stamped on it.

Re: Help -- stuck Morse taper adapter

#7

Here it is for a MT2.....

gil jones

>ENCO........

http://www.use-enco.com/CGI/INLMKD?SIITEM001=292-6225&SIQTY001=1&SICOUNT=1

Gil

Re: Help -- stuck Morse taper adapter

#8

Thanks!

wilbur

>Thanks for all the help!

Re: Help -- stuck Morse taper adapter

#9

#2 wants #2

Mark Mandell - Gone Round In Jersey

>

Re: Help -- stuck Morse taper adapter

#10

Jesper, Denmark

Re: One little addition.....

Jesper, Denmark

>You want to use a hammer to hit the drift key, not a soft mallet. You need a sharp, but short peak force in the direction of getting the #2 out. You could be beating the heck out of it with a soft mallet, and not get it out, but a quick tap with a real hammer kets it loose right away.

Re: Help -- stuck Morse taper adapter

#11

Re: One little addition.....

Bill Howatt

>Jesper is right on the mark. You want a substantial good hard whack not death by a thousand pokes which will achieve nothing.

Bill

Re: Help -- stuck Morse taper adapter

#12

Re: Help -- stuck Morse taper adapter

Bill Grumbine - Kutztown PA

>Where's the Stuck Chuck Canuck when you need him!?! ;-)

Re: Help -- stuck Morse taper adapter

#13

Re: Help -- stuck Morse taper adapter

Jim Rutten

>Looks like these guys have you going the right direction on getting it unstuck, but I want to mention that when my jacobs chuck kept getting stuck in my adapter I got out a magnifying glass and noticed what looked like little round pieces of metal both in the adapter and on the jacobs chuck. I cleaned both thoroughly and rubbed them down with WD-40 and haven't had a problem since.

Re: Help -- stuck Morse taper adapter

#14

Re: Help -- stuck Morse taper adapter

Bill Crommett

>You surely can tell where Bill Gumbine is coming from with a remark like that. I heard the slap of a Beaver tail on that one. But someone needs to give an explanation for the newbys.

Re: Help -- stuck Morse taper adapter

#15

Jesper, Denmark

Re: Help -- stuck Morse taper adapter

Jesper, Denmark

>The Stuck Chuck Canuck is very engineering oriented, and clearly knows that his wrong way rotational experiences have no bearing (!) on this linear friction fit application.

Re: Help -- stuck Morse taper adapter

#16

Re: Help -- stuck Morse taper adapter

Bill Grumbine - Kutztown PA

>Bill, the Stuck Chuck Canuck is a real person, and a highly respected one on this board. Years ago he had an unfortunate experience in that the chuck on his General lathe (what else?) became fastened onto the headstock spindle like it grew there. He solicited advice here on the board, and all sorts of remedies were tried, until at last, he had to go to extremes. He had to disassemble his lathe, and lug the headstock to a machinist, where they were able to remove the chuck for him. His sobriquet was hung on him by one of his fellow countrymen.

Re: Help -- stuck Morse taper adapter

#17

Re: Help -- stuck Morse taper adapter

Jim Shaver - Oakville, Ont

>Yes Bill,

That was awhile ago, Lefty Loosie, Righty Tighty now is my mantra..

Also my Martian Dovetails....a shop of special terms , given to me by my kind woodworking neighbours

Re: Help -- stuck Morse taper adapter

#18

Re: Help -- stuck Morse taper adapter

wilbur

>Thanks, everyone! I received a #2MT drift from McMaster-Carr today, and it did the trick.