Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Heat Shrink Mylar Surface Treatment?

Posts

Heat Shrink Mylar Surface Treatment?

#1

Heat Shrink Mylar Surface Treatment?

charlie belden

>Model plane builders - of planes that actually fly - have to deal with their fuel getting on and possibly destroying their paint job. One of the ways to get around that is to use a type of heat shrink mylar (or some other type of non-soluble in the fuel plastic). This stuff comes in roll, has a heat activated glue backing, and comes in translucent as well as opaque colors.

So what if you cut up a bunch of small pieces, perhaps even in different colors, in different shapes. and applied them to the outside - or even the inside - of a bowl or semi-hollow form?

Just throwing out an idea.

Anyone tried this?

Re: Heat Shrink Mylar Surface Treatment?

#2

Re: Heat Shrink Mylar Surface Treatment?

jfox442

>Used to use Monokote (one of the brand-names of the mylar coatings) on my R/C planes. Process is iron on around the edges--the heat of the iron activates the adheasive. Then either use an iron or heat gun to shrink it between the ribs of the wing or to attach it to the fusalage.

You'd probably be able to use it on the convex areas of a bowl, but on the concave surfaces it'd want to span them as it shrinks and not adhere.

(Some) Potential problems may be: air trapped under the film (stick holes in bubble with pin and re-heat), a lot of shrinkage to control--small shapes will deform with the heat, heat may affect the bowl/object you're attaching the mylar to, the adheasive as it melts can seap out from under the edges of the mylar and get in places you don't want it, and probably a few more that I didn't immediately think of.

You can adjust the heat on a household iron low enough to try it--although the iron will get adheasive on it and you may die a slow death at the hands of the primary user of said iron. (Old irons for sale at thrift shop may be best bet.)

Let us know if you travel this road and how it comes out.

James

Re: Heat Shrink Mylar Surface Treatment?

#3

Re: Heat Shrink Mylar Surface Treatment?

robo hippy

>I agree that it could work on the outside, but there would be problems on the inside as shrinkage would pull it away from the surface. If you could heat some thing that matched the internal radius it might work. If you know some one who makes planes, they probably have a ton of scraps, and might even let you use their iron to try it out. There are special teflon coated irons made just for applying the Monocoat. You could also try a local hobby shop.

I made multiple 'sacrificial victims for the wind gods' gliders in my days as a Hang Glider pilot. Only a ground hog now.

robo hippy

Re: Heat Shrink Mylar Surface Treatment?

#4

Re: WHY?

Russ Fairfield

>I can't think of anything uglier or more useless than a bowl covered with Monocote.

Re: Heat Shrink Mylar Surface Treatment?

#5

Re: WHY?

charlie belden

>Russ noted:

I can't think of anything uglier or more useless than a bowl covered with Monocote.

--------------------

I was thinking of shrink wrapping a piece - as a comment on so much of our world becoming shirnk wrapped - or about those phreakin' plastic bubble packaging - that are a royal PITA to open to get to what you've already paid for.

But I wasn't thinking of encasing, or covering an ENTIRE piece, but rather to just add some small areas of bright, shiny, smooth color. Most of these films are translucent so you could still see the wood grain/figure below. Gilding has been used for quite a while. Why not colors other than gold or silver - in plastic?

BTW - ever eat "fast food"? A McDonalds "burger" is one way to really appreciate a real hamburger, grilled over wood coals - on a fresh baked bun - with real lettuce, a thick slice of tomato and maybe a slice of a good kosher dill pickle on the side. - with PLENTY of napkins of course.

Re: Heat Shrink Mylar Surface Treatment?

#6

Re: WHY?

David Belser

>Charlie, why is a really good question. I saw you post this morning and was going to comment, but had to run off to work. In my opinion, if you are going to make a statement about shrink wrap society, you will need to use a lot not just a few bits.

If you are looking to put shiny color on a piece, why use mylar? Why are you choosing to use something less durable than paint that could be applied using masks? The mylar will have noticeable edges do you want these or are you going to overcoat with something to cover them up?

Lots of questions. Play with it and you may find a creative way to *exploit* the material (rips, tears, bubbles), but if you just want colored patterns you will get higher quality, more durable results with paint.

I have a book with a wonderful work of craft in it - it is a life sized human sculpture made from twigs assembled with plastic zip strips. It is quite possible the artist started by saying "Hey I can use zip ties to hold sticks together". But the reason why the piece works is that the artist got the sculpted human form right.

Good luck and be sure to show us your stuff.

- Dave

Re: Heat Shrink Mylar Surface Treatment?

#7

Re: Heat Shrink Mylar Surface Treatment?

Don Evans

>I'm not sure I follow you thinking on this, but if you are thinking about something that you mask with then remove it after painting this would be better than "shrink" stuff:

http://www.micromark.com/PARAFILM-M,7551.html

Also, in airbrushing world they sell a product in sheets that you cut to the pattern you want and it is known as "Frisket", also comes in rolls. Available at any art supplier and some hobby places.

I've used lot of monokote on rc airplanes and it is great for that job but I don't and wouldn't call it attractive in any way.

Don

Re: Heat Shrink Mylar Surface Treatment?

#8

Re: WHY?

Bob Macgregor

>This lady doesn't use zip ties, but the principle is the same. I guess and artiste has to follow her, or his, muse.

http://www.rense.com/general70/drift.htm