Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Vacuum Pump, How High is safe?

Posts

Vacuum Pump, How High is safe?

#1

Vacuum Pump, How High is safe?

Jorge Castaneda~Downeast Maine

>Hello,

I just had a new development, I was about to do the foot of a platter, turned the vacuum pump on and it went way beyond the 30.

When new, about 3 years ago, it used to go to 28, and of late to 26, the only thing I did was raise it from floor level to a bench top, so I can see the gauge and reach the switch easily.

I know I can just open the valve and let some air in, but what could cause this condition?

Inquiring mind needs to know,

Tnanks

Jorge

Re: Vacuum Pump, How High is safe?

#2

Re: Vacuum Pump, How High is safe?

Russ Fairfield

>You need a new vacuum gauge. A near perfect vacuum is 29.5 in. Hg. Get a new one if it reads above that.

Re: Vacuum Pump, How High is safe?

#3

Thanks Russ,

Jorge Castaneda~Downeast Maine

>I will do

Jorge

Re: Vacuum Pump, How High is safe?

#4

Dennis in Southern Oregon

Re: Vacuum Pump, How High is safe?

Dennis in Southern Oregon

>Just a minor point, Russ. I expect that your conclusion is right, but a perfect vacuum will yield a gauge reading equal to the current atmospheric pressure at that location and altitude and can get over 30 inHg. Dennis

Re: Vacuum Pump, How High is safe?

#5

Re: Vacuum Pump, How High is safe?

Darryl

>Are you certain the gauge is not at fault? Where is it installed in your set up?

Re: Vacuum Pump, How High is safe?

#6

Re: Vacuum Pump, How High is safe?

Wilford Bickel

>If this is a Gast centrifugal pump you can buy rebuild kits that come with new vanes and all new parts for the pump end. Mine was used off of ebay and has never pulled over 27 but I have been using it that way for close to 6 years. I have a rebuild kit sitting on the shelf waiting but it holds so good even at 20 - 27 that I have not needed it yet. You also need to check all your connections, your seals on the chuck and it is very possible to have wood that leaks! I have had pieces that leaked vacuum so badly that I had to wrap them with plastic to get enough vacuum to hold them on the chuck. Remember that you can get too much vacuum on thin pieces and implode them!

I would say moving the pump did not have a thing to do with it UNLESS you unhooked some hoses while moving and need to go back and use some plumbers sealant on them and retighten them. If you are holding good at the current pressures I would just order a rebuild kit and keep running - that is what I have been doing for 6 years. I quite often on thin pieces using my largest chuck will run in the range of 15 to keep from imploding the piece.

Re: Vacuum Pump, How High is safe?

#7

Re: Vacuum Pump, How High is safe?

Bill Howatt

>If the gauge was not in your perpendicular line of sight when it was on the floor you may have had a parallax error reading the gauge. This then got corrected when you moved it up.

In other words, if this is the case, the guage indication is the same as it was before but just looks different.

Bill

Re: Vacuum Pump, How High is safe?

#8

Robinaire, High performance

Jorge Castaneda~Downeast Maine

>Wilford,

It is a Robinaire high performance, 6cu feet.

The gauge is between the intake and the pump, and the problem in not loss os vacuum, the opposite, it reads more than 30, the weather service says 30.25, which corroborates what Dennis said.

Maybe this happened before, but as the pump was in the floor I never noticed.

I sell my bowls and platters to be used, so they are never too thin.

Thanks

Jorge

Re: Vacuum Pump, How High is safe?

#9

Re: Vacuum Pump, How High is safe?

Jorge Castaneda~Downeast Maine

>Bill,

I think you may be right, and now I can see it and as I never saw that happening before I got wondering.

Thanks

Jorge

Re: Vacuum Pump, How High is safe?

#10

Re: Vacuum Pump, How High is safe?

Jorge Castaneda~Downeast Maine

>Dennis,

Thanks for bringing this point up, I am at sea level, right now the weather service says barometer 30.25, and the neddle is about right there, yesterday was even further.

I was not aware that that could happen, so i was worried that could be an unsafe situation.

Live and learn

Thank you!

Jorge

Re: Vacuum Pump, How High is safe?

#11

Re: Vacuum Pump, How High is safe?

Russ Fairfield

>You guys can argue all you want about whether it is 30 or 30.5 or whatever. You will play Hell pulling anything more than 29.5" at sea level with a mechanical pump that cost only a couple hundred dollars or being able to tell the difference on a $10 gauge.

The original message said the measurement was "26 or 28 inches" when it was new and "way over 30" now. 26 or 28 is within the expectation of a small mechanical pump, but "way over 30" is a phsical impossibility.

Re: Vacuum Pump, How High is safe?

#12

Re: Vacuum Pump, How High is safe?

Wilford Bickel

>Russ,

I have to agree with you - I was going by the OP second line that said it went from 28 to 26. This amount of difference on a pump getting some age on it was what I was recommending having a rebuild kit ready but it really did not need it yet. I very seldom turn mine this high as even on my normally thick pieces I have a lot of burls and such that can implode due to the grain changes and weakness. When I reread the original post again and realized he states in the first line he was way over 30 inches Hg then you are correct - this is not possible with a normal shop vacuum system and very, very few lab systems will get to 30 much less above it. I agree - try a new gauge as Russ as suggested!

Wilford

Re: Vacuum Pump, How High is safe?

#13

Re: Vacuum Pump, How High is safe?

Don Evans

>Where does on find the rebuild kits spoken of?

don

Re: Vacuum Pump, How High is safe?

#14

Re: Vacuum Pump, How High is safe? *LINK*

Wilford Bickel

>On my Gast I had to contact Gast directly and they gave me the number of my nearest distributor that was in Atlanta GA. The distributor was able to look up the part numbers based on the numbers on the pump. Then the distributor sold them to me on credit card and shipped them out to me. Link has contact for Gast where you can locate your distributor - can't help on other brands, don't even know if they have rebuild kits.


Gast Contact Page

Re: Vacuum Pump, How High is safe?

#15

Re: Vacuum Pump, How High is safe?

Don Evans

>Thank you