Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Another CSUSA Super Support Story

Posts

Another CSUSA Super Support Story

#1

Another CSUSA Super Support Story

DavidWalser

>I bought a used Woodfast lathe from Craft Supplies USA in 2003. Even if the lathe had not been sold to me "as is", any reasonable warranty would have expired long ago. Over the last couple of years, the lathe would shut off mid-cut. After turning off the power by unplugging the lathe and then blowing out the switches with compressed air, the lathe would work just fine. At first these episodes were infrequent. Recently, they started recurring on a very regular basis.

Last week I sent CSUSA's technical support an email explaining the problem and asking if there was someone in the local area they'd recommend taking the lathe to for repair. In my email, I included my work and home phone numbers in case they had questions. The next day, Roger from CSUSA called me at work and spent a good 45 minutes with me on the phone diagnosing the problem. Following Roger's clear instructions, I was able to fix the lathe myself. It took me several hours -- but that's because I'm a klutz with things electrical, particularly when working in tight spaces.

Anyway, Roger's help went far above what I'd expected. He used up close to 1/8 of his work day to answer questions about a lathe he'd sold me -- as is -- almost 6 years ago.

Re: Another CSUSA Super Support Story

#2

CSUSA Super Support Story comment

Ed Moore in SW VA

>A while back CSUSA figured out that good support equals good business. And we, the woodturners/tool junkies have responded very well to that approach.

What ingredients make up a good support staff? First, the business must prove that they will back up what the tech rep does, allowing them to take chances and go the extra mile. Second, many humans are "problem solvers", and you want someone with a solid chunk of that in his make-up on the tech rep staff. The problem solving tech rep will take a bulldog-like approach to a problem and worry it down until the problem is solved. A tech rep has had a good day if, when presented with a problem, at the end of the day the problem no longer exists. Our modern society needs these people and we couldn't operate without them. The computer world has its "Geek Squads" and we have CSUSA. Thank you CSUSA!

Ed

Re: Another CSUSA Super Support Story

#3

Re: Another CSUSA Super Support Story

Cyril Griesbach

>That's a wonderful story, David, and it great that you take the time to let everyone know. Support like that deserves WIDE recognition and it seems that CSUSA always rises to the top in customer service.

Re: Another CSUSA Super Support Story

#4

Re: David- I also have a Woodfast...

Jamie Donaldson

>...bought new From CSUSA many years ago, and would be very interested in what details you can supply about the repairs they recommended for my lathe maintenance files. I love this machine and still use it frequently, and intend to keep it in top shape for as long as I can turn. Email me privately if you wish to respond.

Re: Another CSUSA Super Support Story

#5

Me too

mfoster

>I also have an old Woodfast lathe with one of the first variable speed drives abvailable. The controllers on mine were made by a turner who lived in the Seattle area and has since passed away (Denver Ulery). I had a few problems with my controller while he was still alive, and he was more than happy to help me out. I have been worried that if my controller gives out I may be out of luck as I know nothing about electronics. I haven't reserched it, but I would imagine that I can find a new controller, but it may need some research as my motor is DC and most of the variable speed controllers now are for AC motors. Luckily mine is still going strong. I would be interested in any info you found.

Mike

mfoster@vermontel.net

Re: Another CSUSA Super Support Story

#6

Re: Another CSUSA Super Support Story

Dinyar Chavda

>David:

Like Jamie, I, too, would be interested in any info. Roger has helped me on many occasions with my 1996 Woodfast.

Mike, I think that the controller on my lathe was also made by Denver Ullery (it has a "D/J Wood Sales" label on it), Roger is very familiar with it, and has sold me parts for it---that might help set your mind at ease on that score.

Re: Another CSUSA Super Support Story

#7

Re: The advice given...

David Walser

>Since a number of you asked, I'll pass on the advice Roger gave me. Note two things: First, the advice may only apply to my situation. Second, what Roger said may seem painfully obvious to many of you. I'm a CPA and don't repair lathes for a living. What he said was very helpful to me. So, if you must laugh, just don't do so whenever we might meet. ("Oh, you're the guy who didn't know... Ha!" Pointing and laughing is very rude behavior, but it's worse when it's done in bed.)

Anyway, with that necessary introduction out of the way, Roger said he thought my lathe might be having two related problems. First, he thought the VFD might be getting too hot. The VFD has a large heat sink that may have become coated with dust that was preventing the VFD from cooling properly. So, he told me where to find the VFD, how to gain access to it, and had me blow it off with compressed air. That took all of 10 minutes. He also suggested leaving the VFD out on the floor for the next 2 or 3 turning sessions so I could see any error codes the VFD might produce. (The manual for the VFD was stored in the tailstock-end leg of the lathe's stand.)

The second problem Roger wanted me to check on was the power switch for the lathe. (In addition to the power switch, the lathe has a start/stop switch to turn the lathe's motor on and off and a variable speed dial to slow down/speed up the lathe.) About a year after I bought the lathe, the power switch quit working reliably. It would take some twisting and vibrating of the knob to get the green power light to come on. So, in frustration, I just left it "on" and turned the power off at the circuit breaker. A year or so later, the green light went out, but the lathe kept running as before. Roger wanted me to clean the power switch by disassembling it. He hoped cleaning it would restore the switch to working order. It didn't. I took it to the local WW Grainger store and they said the switch needed to be replaced. The new switch and the new green indicator light were not the same size as the parts they replaced. (The old light was 3/8" in diameter and the new one as 1/2", for example.) After some effort, which included splicing in the new light (the new switch's terminals were not large enough to accommodate both the 10g power wires and the wires from the indicator light) and other things, I was able to get the lathe buttoned up. She ran as smoothly as ever.

It was too late to start a turning project, but I was sorely tempted to sit in my shop and watch the lathe's one green eye glow in the dark. Instead, I soaked in the hot tub and went to bed.

Re: Another CSUSA Super Support Story

#8

Re: I've never had my VFD out of....

Jamie Donaldson

>...out of the tailstock housing, but did add a remote switch years ago. Maybe I should blow out the area with the compressor to see if any dust has invaded the area without permission? I know there is accumulated dust in the headstock area, and should probably blow that out as well.

Re: Another CSUSA Super Support Story

#9

Re: Another CSUSA Super Support Story

Alex Yeilding

>Thanks for posting this, David. I am relatively new to turning, and part of learning is learning the sources.

On "the other side", Lee Valley shares a similar reputation, particularly with hand tool aficionados, and Rob Lee has a successful business on a quality products/exceptional service model. While their turning supplies are limited, I presume they have the same rep here.

I'm glad to find there is a turning specialty retailer with a similar approach and reputation. They will get business from me.

Re: Another CSUSA Super Support Story

#10

Re: I've never had my VFD out of....

Dinyar Chavda

>Jamie:

The reason I opened my controller was because it was working intermittently. After eliminating a bunch of possibilities that Roger suggested, I sent it to him, and, originally, Roger could find no problems with it (sort of like taking your car in to a mechanic, and it refuses to recreate the noise it's been making all week until you leave the garage!) Eventually, we traced it to a miniscule crack in the circuit board which caused an inscribed wire to lose contact on a sporadic basis. While waiting for Roger's replacement board to arrive, I "shimmed" it with a clip, and it has been working since. Dust did not seem to be a factor in my case.

What kind of a switch are you using for your additional remote switch--I use a basic switch like the one below, and dust is a problem there.


img

Re: Another CSUSA Super Support Story

#11

Re:How weird- I'm using the exact.....

Jamie Donaldson

>...same switch! I've had to replace several when they began to show signs of erratic contact operation no matter how much I tried to blow them out, but for a couple bucks at Lowes a replacement is easy.

Re: Another CSUSA Super Support Story

#12

If somebody wants a spare controller...

Gary Evans Tallassee, TN

>This conversation made me realize I still have the one off my Woodfast laying out here somewhere. As far as I know it only needs a diode or two to make it usable again. That DC motor doesn't appreciate AC current at all.

I'd be glad to hunt it up, pack it up and send it along if someone wants to pay the shipping. I also still have the original switches on the lathe. I don't use them since I've gone to VFD and 3PH motor. If I can get them off, you'd be welcome to them, too.

Gary

Re: Another CSUSA Super Support Story

#13

Re: If somebody wants a spare controller...

Dinyar Chavda

>Thanks, Gary. Appreciate your generosity. It's good to know that this option is available if needed.