Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Maybe I'm just stuborn------WebKitFormBoundary+l6H

Posts

Maybe I'm just stuborn------WebKitFormBoundary+l6H

#1

Maybe I'm just stuborn------WebKitFormBoundary+l6H

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>When I use the Beale buffing system, I only do the first two steps -- not the wax. That's because I've had too many problems with a kind of scarring from using even small amounts of the carnuba wax. Anyone experience this? But I'm beginning to think I should try it again. Still, I worried because of those bad experiences.

------WebKitFormBoundary+l6H3pMgFqosD1VO

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#2

Re: Maybe I'm just stuborn------WebKitFormBoundary

john lucas

>By scarring are you refering to scratches? I had that problem and traced it to dirty buffing wheels. I blew them out with the air compressor and then used the sharp edge of a piece of wood to sort of scrape away any larger pieces of grit. Then I hit them with the compressor again and it solved the problem.

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#3

Re: Maybe I'm just stuborn------WebKitFormBoundary

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>John, No, I should have said, ' burns'; it's more like a smudge that won't go away.

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#4

Re: Wax

Ron McKinley

>Could it be your finish isn't completely dry when you apply the wax? ....Ron

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#5

Re: Maybe I'm just stuborn------WebKitFormBoundary

Stuart Johnson

>This sounds like your have applied too much was to the wheel. I've stopped using carnuba and have gone to Renaissance Wax and like it better.

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#6

Re: Maybe I'm just stuborn------WebKitFormBoundary

Rick_Allen

>I have found that the wax wheel doesn't improve the shine. I have found the wax helps the shine stay longer on the turning.

You might want to clean the wax off the wheel an then apply by hand a thin coat of paste wax, whatever type you like. I am currently using a wax that has a lavender scent. The scent is the "special" quality. The scent last a few days so the impact of that wax is primarily for the pleasure of my wife.

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#7

Re: Maybe I'm just stuborn------WebKitFormBoundary

charlie belden

>As noted earlier, your smudge may be the result of overcharging the polishing wheel.

When I was making jewelry, the words of wisdom regarding the use of polishing wheels was "charge the wheel very lightly, but often".

The other words of wisdom - "stay between 3 o'clock and 6 o'clock" Between noon and 3, if something catches - you catch the flying piece - with your body. Between 6 and 8, if things go wrong - your hands, wrist and maybe the inside of your fore arm get pulled into the spinning wheel. A 6 to 8 inch diameter wheel, even spinning at 500 rpms, rather than the more typical 1750 or 3600 rpms, will run a lot of lineal feet on your arm, generating enough friction to damage skin tissue.

Re: Maybe I'm just stuborn------WebKitFormBoundary+l6H

#8

Re: Maybe I'm just stuborn------WebKitFormBoundary

Barry Elder

>If you can see the carnauba on the wheel, then you have applied too much wax.