Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

1/16 Parting Tool

Posts

1/16 Parting Tool

#1

1/16 Parting Tool

Woodie49

>Anyone have any information a making a 1/16 Parting Tool ?

Thanks

Re: 1/16 Parting Tool

#2

Steven Antonucci

I have a small one

steve antonucci

>I made it from an old saw blade. It's only useful for very small parting depth (1/4" or so).

for really small parting cuts I use an xacto craft/hobby saw. Probably cuts 1/64" or so, and it has a "back" so I can use it to about 1" deep (but it will burn if you run the lathe too fast)

Steve

Re: 1/16 Parting Tool

#3

Fillet Knife

Gil Jones...Georgia

>I use an old Rapala fillet knife as a thin parting tool.

Gil


img

Re: 1/16 Parting Tool

#4

JL

Thanks for the idea!

JL

>

Re: 1/16 Parting Tool

#5

Re: 1/16 Parting Tool

john lucas

>I have a paring knife that I use. For really thin cuts I use a drywall saw that I bought at the flea mkt for $1 bran new. I ground off the teeth and ground it to the shape I like. I can go 2" deep with either of these if I open up the cut just a hair.

Re: 1/16 Parting Tool

#6

Re: 1/16 Parting Tool

Barbara Gill, Remlik VA

>I have a great one that someone made from a piece of a broken Wood-Mizer bandsaw blade.

Re: 1/16 Parting Tool

#7

Re: 1/16 Parting Tool

GalenV in Iowa

>I made this 1/16" parting tool from a Titan rigid stainless steel putty knife purchased from Northern Tool for about $5.98 and cut it to shape with a Dremel cutoff wheel. Hard to cut so so it also stays sharp

Works better than the parting tool I bought before.

Threw it on the scanner so picture not that great.

Galen


img

Re: 1/16 Parting Tool

#8

Re: 1/16 Parting Tool

bill crommett

>I have several made from sawmill bandsaw blades. I will send a piece to anyone wwho will send me his (a generic word) snail mail address. O fcourse you will have to enlist a wood turner or cabinet maker to make a handle for you. To grind the end you are on your own.

Bill

Re: 1/16 Parting Tool

#9

Crommet's Blades :o)

Al Neighbors

>I have one of Bill Crommet's offerings. It's the best little parting tool I've ever used, and stays sharp longer than my converted butcher knife.

Thanks, Bill... you're a gem!

Re: 1/16 Parting Tool

#10

Bill Crommett, email failed...

jwoodwright

>Bill, Hotmail sent a delivery failure... Please email me as I would like some of your blade stock. This has worked in the past when they wouldn't permit an outgoing email... I appreciate this. John Kaner

Re: 1/16 Parting Tool

#11

Re: Bill Crommett, email failed...

Woodie49

>The Same for Me.

Thanks

Re: 1/16 Parting Tool

#12

Re: 1/16 Parting Tool

gil jones................georgia

>Thanks, Bill, below is the response I received when emailing to your address as listed on this post thread.????

Gil

=========================

This Message was undeliverable due to the following reason:

Each of the following recipients was rejected by a remote mail server.

The reasons given by the server are included to help you determine why

each recipient was rejected.

Recipient:

Reason: User unknown

Please reply to

if you feel this message to be in error.

===========================

Re: 1/16 Parting Tool

#13

Re: 1/16 Parting Tool

gil jones................georgia

>Also, I have used a sliding T bevel as a thin cutoff tool.


img

Re: 1/16 Parting Tool

#14

Re: 1/16 Parting Tool

Skip Beardsley------WebKitFormBoundarylsHY4+4w161B

>Since my sawzall box was full of some not so sharp blades I converted a couple to thin parting tools. They come in both long and short versions so I made two handles and have one of each. I can go at least four inches deep with the long one if I an careful and open the kerf just a bit.

One suggestion, use good name brand blades like Lennox or Milwaukee. Box store blades do not work as well.

Skip

Re: 1/16 Parting Tool

#15

Re: Bill Crommett, email failed...

Bill Crommett

>try this ; wecrom@nctv.com

Iam having computer problems, but we will keep at it until you can find me. Bill