Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Stamping then scraping then waiting - Embossing

Posts

Stamping then scraping then waiting - Embossing

#1

Stamping then scraping then waiting - Embossing

charlie belden

>I saw a video of a guy using leather stamps to texture end grain, compressing the wood that was stamped.

A well known furniture maker, Frank Klausz, makes what works essentially like an O-ring seal for a water proof box. He uses a piece of steel wire hammered into the edge of the sides to create a compressed grain groove. He then planes that edge 'til the groove is gone. When water is applied to the edge, the compressed grain swells back to its uncompressed size, rising above the unstamped and planed surface - like an O-Ring.

So - what would happen if you tried that on the compressed/stamped end grain. Stamp it, turn off enough wood to get down to the bottom of the stamped area, then dampen the surface. Would you then get a true embossed pattern (pattern rising above the background as opposed to being down into the background surface)?

Re: Stamping then scraping then waiting - Embossing

#2

Re: Stamping then scraping then waiting - Embossin

Rick_Allen

>yes

You don't have to limit this to endgrain.

This technique has been used by some wood carvers to put small bumps on a carved frog.

This technique also works with side grain.

I have used a 15 ton press to emboss with leather stamps, turn off and steam.

Dense woods don't emboss much at all. I would suspect that endgrain would also be difficult to emboss. Very high embossing pressures would be needed and very small patterns.

When embossing you want to make sure the wood fibers don't get broken. The goal is to bend and compress the wood fibers. You want to avoid breaking any fibers.

Re: Stamping then scraping then waiting - Embossing

#3

Steven Antonucci

Answer (again): yes

Steve antonucci

>Like Rick said, you can do this on more than end grain. One of our club members show this technique to mimic ostrich leather. Using a small punch, made some holes,then turned away to the bottom of the hole and steamed the bumps up.

I have a project in my head that will use this technique (someday...)

Steve

Re: Stamping then scraping then waiting - Embossing

#4

Re: Answer (again): yes

john lucas

>I have experimented with this and find that it's hard to get even results. It changes depending on whether the stamp is in summer grain vs winter grain, end grain vs side grain etc. It works most of the time but the lumps don't always come out the same height. I was trying to replicate brail. As a random texture it works great.

Re: Stamping then scraping then waiting - Embossing

#5

Embossing - Yes

David Belser

>As others have said you can use this technique on any grain. I also have several ideas and have done limited experiments. I "discovered" this when I learned how to repair dings and dents - You can accomplish some amazing repairs on a banged up piece by allowing water to soak into the dent and then hitting it with a small hand iron - (I've had more practice with this than I'd like to admit! :)

You don't need to use steam, when I make small finger tops, they get a soak in shellac when they come off the lathe (they soak for as long as it takes to make the next one). I've experimented with a few different was of denting the wood before turning the final shape (BB's, side of a nail...) The top comes off the lathe perfectly round, after the soak, the wood swells back to it's original un-dented shape causing bumps on the top.

Do some experiments and have fun, be sure to show us the results. As John said, it is hard to control the amount of bump.

Re: Stamping then scraping then waiting - Embossing

#6

Re: Embossing - Yes------WebKitFormBoundary4yJQDk6

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>I wonder if this technique would work on a lidded box to get that nice snap that we usually hope to get by turning a slight ridge in the male part where the lid fits.

------WebKitFormBoundary4yJQDk61P+aArqv0

Re: Stamping then scraping then waiting - Embossing

#7

Brad Vietje

See Decorating Turned Wood (O'Donnell) *LINK*

Brad Vietje

>All,

This technique is described and pictured in Decorating Turned Wood: The Maker's Eye, by Liz & Michael O'Donnell, published by Guild Of Master Craftsmen.

Safe spinning,

Brad Vietje

Newbury, VT


Decorating Turned Wood

Re: Stamping then scraping then waiting - Embossing

#8

bayonet fit

john lucas

>I've thought about trying that to make a bayonet fit lid but then decided it would be easier and more controllable to just turn a bead and mill away the parts you don't want so I never tried the dented wood technique.

Re: Stamping then scraping then waiting - Embossing

#9

End grain v. long grain

Alex Yeilding

>I'll be interested in hearing your results. It seems to me that the Klaus techinique would be more effective than a depression line crossing the grain, which in turn would be more effective than a depression in end grain. Think of the soda straw bundle model of wood. Klause is compressing the side of the stack, leaving compressed but intact cells that "want" to return to their natural shape. In end grain, you are mainly smashing already cut cell walls, which might have less "memory" than an intact cell.

But then again, I may be totally washed up here. Just my guess.

Re: Stamping then scraping then waiting - Embossing

#10

Re: bayonet fit

Russ Fairfield

>The advantage of the turned bead is that it will always be round and you control the diameter. The compressed wood bead may or may not expand back to where you want it, and it may not be the same all the way around the circle. Beasides that, adding water to a tight fit where the wood is thin isn't a good idea.