Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

hollowing a round ball

Posts

hollowing a round ball

#1

hollowing a round ball

john lucas

>I tried hollowing one of the Holly balls that had a rotten limb defect. Most of the way through it dawned on me that I didn't have any way to check the thickness of the lower half. I was using a jam chuck. By drilling to the finished depth I was able to get the whole thing fairly thin but it was thick in the 4 oclock to and 7 oclock areas because I chickened out. All I could do was go into the drill depth and try to imagine a circle and then trace that arc mentally.

I suppose I could cut a slot in the side of the jam chuck so I could reach in and measure. Another option would be to accurately draw a circle on the jam chuck and use my lazar pointer on a captured bar system but that would only work if you draw the half circle accurately enough.

Re: hollowing a round ball

#2

Re: hollowing a round ball

Greg Haugen

>John,

A while ago our club had Stuart Batty for the weekend and he demonstrated one of his sphere boxes. He had a paper cutout of a circle that he was using to go along with the drilled depth hole as a template to see if he continued to hollow in a "sphere". It seemed to work out pretty well.

Greg H.

Re: hollowing a round ball

#3

Re: hollowing a round ball

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>One way, perhaps, would be to go as deep as you dare and then turn the sphere around in the jam chuck. Then drill some very small holes in the thick part, which is now exposed, and turn the remaining sphere on the outside to final thickness using the small holes as a thickness guide. Finally, fill in the small holes with sawdust and glue and finish. I'll bet it would work great.

Re: hollowing a round ball

#4

Re: hollowing a round ball

Russ Fairfield

>Leave it thick on one side and it will always roll to the same position and not roll off the table.

Re: hollowing a round ball

#5

Peter Lamb, in SC

Re: hollowing a round ball

Peter Lamb, in SC

>Great suggestion Russ!!

Re: hollowing a round ball

#6

I'm not following you here...

Paul Zerjay

>Wouldn't 4 o'clock and 7 o'clock be on the opposite side of the jam chuck? Why would you need to cut a slot?

Re: hollowing a round ball

#7

Re: hollowing a round ball

john lucas

>I've turned sphere's in two parts. That's easy. I'm talking about hollowing through one hole.

Re: hollowing a round ball

#8

Oh, that's why I left the bottom thick. :)

john lucas

>

Re: hollowing a round ball

#9

Re: I'm not following you here...

john lucas

>I'm not sure 4 and 7 was a good choice. What I'm talking about is the bottom half of the ball that's buried in the Jam chuck so you can't see it or get tools in there to measure. The slots would let me touch the outside of the ball through the slot to be able to measure with a C shaped type measuring device.

I may try that tomorrow. I still have the jam chuck I made although it may have changed shape already and be useless.

Re: hollowing a round ball

#10

Re: hollowing a round ball

Joe Flemig

>John,

It's a jam chuck. Pull it out, caliper it, then jam it again. I do that all the time with spheres. But you my protest: "Joe, if you pull it out and re-jam it, it won't be centered on the original opening."

Not a problem. First, a sphere works off center. Geometry of a sphere assures this for you. Besides, you can always get close to centered by bringing up the tailstock to locate dead center, and then adjusting the jam if needed. Second, start with an opening just a little smaller than you intend. When you get to the final thickness, jam it one more time and true the opening up.

Joe Fleming

Re: hollowing a round ball

#11

Re: hollowing a round ball

Juergen

>All is not lost. Just apply a needle scaler, some gray primer, red dye and finish with lacquer


img

Re: hollowing a round ball

#12

Re: hollowing a round ball

Juergen

>OOOps!! Wrong thread

Re: hollowing a round ball

#13

LOL :o)

Al Neighbors

>

Re: hollowing a round ball

#14

Gotcha. I like the "slots" idea to measure.

Greg Haugen

>

Re: hollowing a round ball

#15

Re: hollowing a round ball

mike Nelson

>What wood do you use for the chuck? Is it wet, to keep the ball from turning?

Re: hollowing a round ball

#16

Re: hollowing a round ball

john lucas

>It was wet. I don't remember what is was just something on the floor from earlier cutting.

Re: hollowing a round ball

#17

Re: hollowing a round ball

steve worcester

>If you could find a laser that will project an arc or a circle, you could project it up above the lathe and adjust the height to get a smaller or larger circle (I did look and didn't find one).

Although, Pascal Oudet is going to demo at the symposium how he does it. His are split somehow along a grain line and rejoined. I may actually have to see that demo.

Or get trained worms.