Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Hollow form - - process questions

Posts

Hollow form - - process questions

#1

Hollow form - - process questions

Pete in Holland, MI

>Hey all -

Am venturing into the hollow form arena using my Jamieson-like rig. Having fun and learning with each vessel that I turn. All thus far have been green-turned.

Couple questions of ye:

1) Is wood movement as it dries (going typically oblong) a fact of life? Most pieces have been turned from half of a log (keeping clear of the pith), with the top & bottom of the vessel being the end grain. Woods used to date have been poplar & maple. Once turned, they live in a paper bag for a week or so before being allowed to live in the outside world.

2) Do you guys pay a lot of attention to finishing all of the tool marks? Kinda tough to do with a small cutter bit. I'm making sure that the ID, within finger reach, is as smooth as I can get it.

3) Is there such a thing where vessels are twice-turned, like a bowl? Major rule changes from the bowl know-how that I am familar with?

Vessels have been 3-8" diameter and 7-10" tall thus far.

More questions will be coming.....I'm sure.

Pete

Re: Hollow form - - process questions

#2

Re: Hollow form - - process questions

Al Neighbors

>Question 1, Most woods all have different amounts of radial to tangential shrinkage. The most stable of woods is Mesquite. I�ve turned Mesquite HFs green, and most were still round when sold. The thinner you turn them, the less cracking there will be, but nearly all wood will warp while drying. Oval is nice, sometimes. :o)

Question #2, I suppose you mean on the inside� I use ring forceps to hold sandpaper and a piece of stiffening rubber, if I can get it inside. If I can�t, I put the chuck and HF on a tumbler (58rpm), and put granite pebbles and Aluminum Oxide chunks inside and let it tumble for about 8 hrs or so. This makes it smooth, but wavy, due to the softer grains wearing away quicker than the hard grain. If you make the entrance hole small enough, you don�t have to worry about the smoothness of the inside; some folks use black gesso on the inside, so they can't see in.

#3, yes, some folks roughturn hollowforms and then soak in the LDD or DNA and then later, re-turn.

HTH

Re: Hollow form - - process questions

#3

Re: Hollow form - - process questions

robo hippy

>End grain will shrink and warp just like flat grain, though not as much. The part towards the center of the tree will move less than the outside part of the tree, and the sap wood can move a lot. Reaction wood (figured wood), burl and stressed wood (like where it buttresses out at the bottom of the tree) will move a lot 3 dimentionally, as in the ripples will end up being little waves, and pieces can warp more to one side than the other. Of course, larger pieces will move more than smaller ones, and drier wood from desert regions will move less than ones from wetter areas, and spring wood moves more than fall/winter wood. You can twice turn them. I prefer to plastic wrap them, covering the entire outside with plastic stretch film, and leave the inside open. Some times I will seal the end grain on the outside with finish. When a piece is highly figured, I try to get a finish from the tools that won't need sanding, or wet sand with an oil finish so the 3-D surface will remain. Some move so much, I couldn't return them if I wanted. You could probably get away with less than the 10% rule (10 inch bowl, 1 inch thick walls) if you want, but I wouldn't attempt it, better safe than sorry.

robo hippy

Re: Hollow form - - process questions

#4

Re: Hollow form - - process questions

Eduardo sarmiento-hall

>Hi I ussualy turn my hollow forms 2 or 3 times wood does move some more than others,tha vase I have put here will be return in a week and in about 10 days will be sanded and finnished

Re: Hollow form - - process questions

#5

Re: Hollow form - - process questions

Wally Dickerman in Arizona

>Pete, end grain pieces will distort as they dry but not as much as face grain pieces.

I seldom finish turn a wet blank. I prefer to rough them out and slather the outside piece with Johnson's paste wax. You can use Anchorseal. Just takes longer to dry. I put a date on the piece. In 6 months it'll be dry enough to finish turning. If it's really wet I paper bag it for a few weeks. Nothing wrong with doing once turned pieces, just my preference.

When you are doing the inside, completely finish the area around the rim. After the wood distorts, even just a little, you can't come back and work on it.

Wally

Re: Hollow form - - process questions

#6

Steven Antonucci

Here in NJ...

Steve antonucci

>Winters are cold, garage is heated. Thick, wet wood will crack.

Summers are hot and humid. Thick, wet wood will crack.

I finish turn almost everything to 1/4" or less, and most things warp a little bit, but not so much so that you notice it from across the room. Beech will crack no matter wht you do, so I just plan it into my design...

Steve

Re: Hollow form - - process questions

#7

Brad Vietje

Yup -- That about covers it.

Brad Vietje

>