Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Hollowing help needed...

Posts

Hollowing help needed...

#1

Hollowing help needed...

Marc Phillips

>I would appreciate any and all comments... and tips, hints, help, web sites, good videos, .... anything at all!

I just finished hollowing a 9" deep vase... about 5 inches at the widest point, with a 3" opening at the top with a slightly raised lip.... it started to crack and split, and after using CA it is out soaking in boiled linseed oil.... probably wont make it, but not why I am posting :)

I have Randys Monster Tool hollowing set, which is a long bar and an assortment of cutters... the teardrop shaped one, and some cutters... I also have the Sorby Multitip tool...

So... I shaped the outside, no problem at all... then reverse chucked and used a large forstner bit to hollow out the inside... again, went smooth, no problem.

Here's where I struggle.... using the hollowing tools.

What I am completely unsure about, and having a lot of trouble with is the combination needed with the tool rest height, cutting sequence, and which cutter to use. I somehow make it through until the piece is finally hollow, but it is more like a battle instead of a hollowing exercise.

I did change the grind on the cutters (teardrop shaped) and flattened the back first before grinding on the grinder... and that did help... started getting larger shavings instead of just dust...

I could use some help... any information you would like to give would be appreciated.

Re: Hollowing help needed...

#2

Re: Hollowing help needed...

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>It's a bit hard to figure out why you're having trouble from what you've said so far. The height of the cutting tip should be just about on the center line of the lathe spindle. It's very important that it be sharp! If you are using a swan neck tool, make sure the tool is supported on the tool rest BEHIND the curve of the tool. This means further toward the handle of the tool. Otherwise the torque caused by the cutting will tend to twist the tool badly. If the grain of the wood is parallel to the lathe bed, then the general cutting motion should be from the inside toward the outside. For faceplate grain direction, you should be making small circular motions that move from the outside toward the inside --even if you start out more or less near the center of the piece after drilling your hole. This hardly scratches the surface, but check out what I've have suggested.

Re: Hollowing help needed...

#3

Re: Hollowing help needed...

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>Now that I am thinking about it, you probably want to get a good hollow turning video. One of the best is by John Jordan. That's how I learned when really very new to turning and all was well.

Re: Hollowing help needed...

#4

Steven Antonucci

Simple guide to hollow turning

Steve antonucci

>1.) Drill out the middle close to final depth. use the widest and longest bit you can fit through the opening. If using a spade bit, stop short unless you want a little hole in the bottom of the pot.

2.) Hollow the first half of the pot about half the length. This gives you freedom of movement inside and the shavings get packed away from the centerline of the pot. Empty often with compressed air.

3.)Once the top of the pot is half hollow, work your way down from rim to the half way point about 1" at a time to final thickness. Once you have verified thickness, do not cut the top of the pot again.

4.) If you are turning "bowl orientation", you can hollow out the bottom half of the vessel with a bowl gouge with the flute at about 2 o'clock. The bottom of the pot cuts very quickly this way, and it's surprisingly easy to control.

5.) if you are turning spindle orientation, continue working down 1" at a time cutting toward the opening in the top. If you pull the tool straight back, you will eventually cut air when you enter the first half. Then, move back to the start of the cut, and repeat until the tool doesn't cut air (wall in the new 1" of cut section equals the wall in the top of the pot.) repeat down the length of the pot, blowing out dust frequently.

At all times, it pays to be on center or just ever so slightly above (1/8" max). A sharp tool should hiss when it cuts, and you should hit it with a diamond stone every time you stop to blow out chips. Measure, measure, measure...

Steve

Re: Hollowing help needed...

#5

Steve Kubien

Re: Hollowing help needed...

Steve Kubien

>My suggestion is Lyle Jamieson's dvd on hollowing since you are using a captured rig. It is excellent. The only one I have seen using hand-held tools is Mike Mahoney's, also excellent.

Wish I had more to offer.

Steve

Re: Hollowing help needed...

#6

Re: Hollowing help needed...

Pete in Holland, MI

>I started some hollowing with a Sorby swan neck tool. Keeping it at, or slightly above center as you get deeper is tough and pretty stressfull. Exciting to say the least as the tool grabs.

I opted to build a Jamiesion-like system. With many old machine parts available for purchase at work, it cost me about $40 to build & I am very pleased with the performance. The jig keeps the tool bit at a constant height, and with the laser feedback system, allows you to concentrate on shaping and form.

Regarding your cracked piece:

1) Wood cannot have any hints of cracks going in. They will only get worse.

2) Wood thickness needs to be uniform thru your vessel.

3) Mid turning, if you need to step away, even for a few minutes, cover your vessel with a plastic bag to keep it wet. Green hollow forms need to go from start to finish as quickly as possible.

4) My turnings go from the lathe to a closed paper grocery bags for several days to control drying, thus cracking.

Good luck !

Pete

Re: Hollowing help needed...

#7

Re: Hollowing help needed...

john lucas

>Ditto what pete says. I often spray the outside of hollow turnings to keep this area as wet as the inside. This has eliminated the checking while turning and also slows down the warping.

Re: Hollowing help needed...

#8

Wow...

Marc Phillips

>I am not doing ANY of that! ... talk about a wake up call!

Thanks... guess I now know why my latest vase cracked... left it on the lathe for about 4 hours when I had to go pick up the kid at a church activity...

Learning all the time... and that = fun for me!

Re: Hollowing help needed...

#9

Re: Hollowing help needed...

Marc Phillips

>Thanks John... spray with just water?

Re: Hollowing help needed...

#10

Plain or soapy....

Al Neighbors

>I'm like John Lucas in regard to keeping the outside wet. I've got an old 409 spray bottle that I use. I spray the outside of green wood pieces with soapy water... I think in my hot, dry, West Texas climate, that the soapy helps it not evaporate too fast... but keeping it wet on the outside, while you turn out the inside will delay the wood's desire to crack.

And, if the finished piece has a foot on it, it's best to make the bottom concave. If the bottom is thinner than the sides, it will not crack as much when drying... at least that's my experience... I think it's because the thinner bottom allows it to move before the sides crack. (could be all wet, here) :)

Re: Hollowing help needed...

#11

Re: Hollowing help needed... *LINK*

John Jordan

>Try this.

John


Hollow vessel