Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Moving Oneway Lathe ???

Posts

Moving Oneway Lathe ???

#1

Moving Oneway Lathe ???

E.T.

>We want to move a Oneway 2036 from a garage to another location and back again. No stairs are involved - all on one level. Is there an easy way to get this job done without damaing the lathe or ourselves. I don't know if the owner has the wheel kit and we will probanly be using a pick - up truck to do the move.

Thanks, ET

Re: Moving Oneway Lathe ???

#2

Re: Moving Oneway Lathe ???

Don Evans

>I learned long time ago that moving stuff isn't my thing, especially heavy stuff. I've moved households several (7) times and always used moving companies.

So on the last move, I hired them again and all my tools had to go into the garage as we were downsizing and no shop. Once the shop was build, I called the movers and they sent 4 guys over to move the machines from garage to the shop.

Then I replaced the Nova 3000 with a Oneway 2436 and it was delivered to my garage again, driver alone used a hydrolic pallet jack to wheel it down driveway into garage. I then called the movers again and they sent over 4 guys who picked it up by hand and set it on a wheeled cart and wheeled in around to and into the shop, picked it up off the cart and set it down on floor. I had a piece of 3/4" plywood that was layed down to get it into the door of shop.

Point is that only cost me $150.00 for the 4 guys and it took them 15 mins, they do this all day long for a living and know what they are doing. None of my friends and neighbors (who don't know what they are doing) got hurt. I am over cautious with this type thing, cause what would you do if friend hurt his back and could never work again, not worth it.

Hire professional and unless you are in a large metro area it may be cheaper than you think. Worth a couple of calls to price it out and let them worry about how to do it.

Don

Re: Moving Oneway Lathe ???

#3

Dick Hines

Re: Moving Oneway Lathe ???

Dick Hines

>Unless you have access to a fork lift I would forget the pickup option. Try to find a flat bed trailer or a truck with a lift gate.

Put 3/4' plywood down to move it on. You can make a palet to move the lathe on. All it takes is a couple of 4x4's and a set on good wheels. Jack up the lathe and place the palet under to lathe. Strap said lathe to palet and you are set.

Re: Moving Oneway Lathe ???

#4

Steven Antonucci

Assume the two locations are not close?

Steve antonucci

>I am guessing that you have to cover some distance that requires loading it into a truck? If not, I would build a dolly and just lift it onto the dolly to roll it.

Should be able to do this with 2 strong guys...

Steve

Re: Moving Oneway Lathe ???

#5

Yes...

Peter Teubel

>...with a Oneway wheel kit, a ramp trailer, rope, and 2 pulleys (elec winch optional). From experience in moving mine, these items make it quite easy with only two people.

Sounds like you're moving the lathe to a demo.

Re: Moving Oneway Lathe ???

#6

Re: Assume the two locations are not close?

Michael Mocho------WebKitFormBoundarygRbxIAUPMcCra

>This may sound crazy, but it really works, as long as you have 3 or 4 alert folks with good balance, and are moving over relatively level ground and shallow ramps:

I have move several full-sized Oneway lathes using only a heavy-duty two-wheeled (vertical style) dolly. The dolly should be stout, and the wheels must be large enough and not too soft. The trick is to slip it under from the headstock side- grabbing the edge of the leg assembly plate, and using a short 2x4 spacer just the width of the dolly under the edge of the steel plate, lift the tailstock end up quite high until the balance point is found. With a person walking on both sides of the tipped-up lathe to help balance it, and the person with the dolly keeping it tilted waaaaay back to keep the center of mass above the wheels, we have moved lathes up ramps, around corners, and through a normal sized door with great success. Letting the lathe down slowly in the new location requires team effort, and blocking the wheels on the dolly so it doesn�t shoot back. Since most of the mass is on the headstock side, the dolly carries the weight without causing hernias on the folks balancing it. It helps to remove the tailstock and tool rest base, and secure the pendant control arm from swinging.

Of course it is essential to have a LARGE two wheeler- not the type used for moving appliances since it must have wheels that are at least 6�-, and several attentive friends to help balance the monster once it is up on the air.

I learned this from Michael Hosaluk, who directed us in the moving several large lathes at the Emma Lake collaborative event. Brains, not muscle.

Re: Moving Oneway Lathe ???

#7

Re: Moving Oneway Lathe ???

E. Tabachek

>Thanks, everyone.

I really like the idea of hiring machine movers with a power tail gate to do the move. They are experienced and would have insurance, too.

But, if we do have to do it ourselves with the pick up truck, should we remove the legs? Yeah, I guess that's the only way to get the bed into the truck. Is this a tricky job? How many guys do we really need?

Again, thank you. ET

Re: Moving Oneway Lathe ???

#8

Eight Hundred POUNDS ???

E. Tabachek

>I just checked the weight of this machine at the Oneway site. Really ??? 800 pounds ???

ET

Re: Moving Oneway Lathe ???

#9

Re: Moving Oneway Lathe ???

Doug Thompson near Cleveland

>This would be a bear to lift onto a bed of a pickup truck, a trailer would save your backs. No matter what you decide strap the lathe down tight so it doesn't fall over. I have to move a lathe next week, at 5,500 lbs. riggers will do it.

Re: Moving Oneway Lathe ???

#10

Re: Moving Oneway Lathe ???

Mike Cunningham (Cape May NJ)

>I've moved three Oneway's, one of them a 2436 twice with just a friend helping. Disassemble into the various sections and simply carry them. The ways which are the heaviest item can be moved via a sturdy handtruck. Set one end on the tail gate, lift the opposite end and slide into the bed. Easy when they're are no stairs involved.

Mike

Re: Moving Oneway Lathe ???

#11

Another ???, Mike

E. Tabachek

>Mike: Do you leave the headstock attached and the motor in place in the tube? That bed must still be very heavy and we would have to be careful as we move it ( so as not to pull some important body part. !!!

ET

Re: Moving Oneway Lathe ???

#12

Yes and No

Mike Cunningham (Cape May NJ)

>On my 2436 we removed the headstock but left the motor in place. Disconnected the controller and removed both legs. Labeled the wires and also made a diagram. Yes the bed is quite heavy, obviously the heaviest part of the machine but two of us were able to handle it placing one end on a hand truck then lifting the opposite end and with both of us balancing and holding on wheeled it to the pickup. Laid one end on the tailgate, we both lifted the opposite end then slid it in.

I had a lumbar fusion in June '06 and was able to do this last summer, of course perhaps my behavior is the reason I needed the earlier back surgery ;^)

My 2436 is a bit heavier than the machine that you're moving, moved one of those also and did it the same way. If you're concerned about lowering the bed from the legs to the floor use a cable, chain or rope from overhead if possible, but I didn't need to do that. I moved my old Vicmarc VL300 the same way. Get one or two helpers, think before unbolting and moving things, take your time and you'll be fine.

Mike

Re: Moving Oneway Lathe ???

#13

Great info

Mike Cunningham (Cape May NJ)

>If need be one can lift the lathe via a floor or bottle jack to get the hand truck/dolly beneath it.

Re: Moving Oneway Lathe ???

#14

ps: Michael

Mike Cunningham (Cape May NJ)

>I attended two of your rotations at Totally Turning.......twice. Thanks for a great job.

Re: Moving Oneway Lathe ???

#15

Re: ps: Michael

Jim Rutten

>Had a Oneway 1640 that was going down into the basement. First, thing we did was bought a new dorr and had it installed so it was straight to the basement and not a 90 degree turn. Then we attached an electric winch to it and ran it down a plywood ramp with myself and my FIL guiding it and my MIL on the winch controls. It only got out of line once, halfway down the stairs and I thought we were done for. My FIL says no problem and has me hand him a 4' long 2X6 and levers it back straight. I don't relish the time when we will have to move it again.

1 Oneway 1640 lathe: 3000+ dollars

1 Oneway wheel set: 120 dollars

A FIL with the common sense to help you get the job done: priceless

Re: Moving Oneway Lathe ???

#16

hire a piano mover

John K Jordan

>Those guys have the proper equipment and know how to move very heavy things. My Baldwin grand probably weighs as much or more than the lathe.

JKJ