Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Sharpening a chainsaw

Posts

Sharpening a chainsaw

#1

Sharpening a chainsaw

Marc Phillips

>Got a new chainsaw a few weeks ago, and have been cutting up some logs for bowls with it.... since this is a larger saw than I currently have I guess I expected better performance... 33cc VS 46CC .... I dunno, guess I just wanted to really see a difference... and these was not really any at all, other than a larger capacity... 20" VS 16"

... anyhoo...

The chain on my smaller chainsaw was sharpened by a service at a hardware store... and the little rascal sure goes through the logs pretty well...

so...

I figured maybe these are like bandsaws.... you know, the blades that come with the saw are terrible....

Went to Lowes and bought a pair of those little skinny grinding stones labeled "Chainsaw sharpening stones"

Eyeballed the chain... pretty sure I know how this works... and went at it... sure seemed easy.

.... moment of truth.... Wow... blew right through an oak log like it was balsa! .... gotta love that eh!

So... now I an wondering if it could be better, so I come to y'all with this question....

Should you sharpen the gullet first, then the flat top?... or do the top, then the gullet?

..... or maybe the top, gullet, then another pass with a fine stone across the top?

Whaddya think?

Re: Sharpening a chainsaw

#2

Re: Sharpening a chainsaw *LINK*

GalenV in Iowa

>Best to view Stihl's video.

I am not the best person for doing what's right and it is good to review more often.

I tried the Dremel stones and went back to the hand file for a better control and sharpening.

I assume you mean the depth gauge and not top of tooth. Depth gauges last.

Toughest job I used the chain saw on was cutting railroad ties for retaining wall. The ultimate test to any saw but hope not too many try to check it out unless you intend to get rid of the saw.

Safe cutting!

Galen


Stihl video

Re: Sharpening a chainsaw

#3

Re: Sharpening a chainsaw

Pete in Holland, MI

>Should only sharpen the gullet. If sharpening the teeth on the top of the bar,force the grinding stone directly towards the motor, not down or up. With the right diameter stone for your chain (manual should show that), this is all you need. Should never have to grind on the top of the tooth. Make sure to maintain the angle of the tooth. About half way thru the life of the chain, file a few thousands off the top of the depth limiter just ahead of the tooth. Too much off of here, and the chain will take too big of bite and lug the engine. Not doing this will keep the tooth from digging into the wood.

This is what I do. I used a Dremel for my work.

General rule of thumb: Look at the tooth closely. If you can see light reflecting from the cutting edge (top edge) of the tooth, that means there is a flat there to reflect the light, and it needs sharpening. Like a lathe tool, the difference between "really sharp" and "kinda sharp" do make a difference.

Good luck !

Pete

Re: Sharpening a chainsaw

#4

Re: Sharpening a chainsaw

Bill Crommett

>Pete said it all !

Re: Sharpening a chainsaw

#5

Re: Sharpening a chainsaw

Marc Phillips

>Thanks all... I appreciate the help. With the comments and video I feel like I understand what I am supposed to be doing now to sharpen the chain...

Thanks again...

Re: Sharpening a chainsaw

#6

Re: Sharpening a chainsaw

Texian

>Watched the first few seconds of the Stihl video and shut it off when I observed that they were sharpening the chain ON the bar. Better IMHO to remove it so that the filings do not fall into slot of the bar. Granted when sharpening in the field that's the easy way to do it, and maybe it does not really matter. I use a chain file of correct size for the chain, chuck file in cordless drill and hold free end with scrap block of wood. Note direction of file teeth and set drill direction (fwd or rev) accordingly. Grip chain in bench vise and file 2 or 3 teeth, move chain and repeat. Reverse chain in vise and repeat. Eyeball file angle to match leading edge of teeth. Guess this may not be good procedure, as I seem to do some things differently than other folks. But it works for me.

Re: Sharpening a chainsaw

#7

Re: Sharpening a chainsaw *LINK*

Mike Jones, Redding, CA

>this may be your consumate source of information for all things saw-chain related. The info here, can be applied to any brand of chain, not just Oregon.


http://www.oregonchain.com/faq.htm#sharpening