Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Nova Ornamental Turner

Posts

Nova Ornamental Turner

#1

Nova Ornamental Turner

Bill McWhirter-

>Does anyone have any experience with the Nova Ornamental Turner?

The company website mentions an adaptor that allows it to be used on a Powermatic 3520B but I can not find it listed on the order form.

I would really like some information on this lathe accessory before laying down the cash, but apparently you can only get it direct for Teknatool and they only have a New Zealand phone number.

Any help appreciated.

Re: Nova Ornamental Turner

#2

Re: Nova Ornamental Turner

john lucas

>Bill They had on one the shelf at the Franklin Tn Woodcraft store the last time I was there which was several months ago. I looked at it because I've always wanted one. It seems like it's built quite well and would do what it's designed to do. I've never actually been able to turn with one however so I can't answer your questions.

Re: Nova Ornamental Turner

#3

Re: Nova Ornamental Turner

Ralph

>Contact the distributor for you nation, in the US that is Tim Geist

http://www.teknatool.com/Contact.htm

Re: Nova Ornamental Turner

#4

Re: Nova Ornamental Turner

Bill McWhirter-

>Sent an email several days ago. Got no response.

Re: Nova Ornamental Turner

#5

Re: Nova Ornamental Turner *LINK*

Fred Holder

>I've had an Ornamental Turner for the Nova 3000 and the Nova DVR for several years. It is a good tool. I don't know about the adapter that you want, but I suspect that they have one. Try e-mailing Roger Latimer at Roger@teknatool.com should be able to give you the straight scoop on the Ornamental Turner.


More Woodturning Website

Re: Nova Ornamental Turner

#6

Re: Nova Ornamental Turner

Ralph

>Tried calling?

Tim is reported to be terrible at responding to e-mails. But he has responded to my questions in the past

Re: Nova Ornamental Turner

#7

Re: Nova Ornamental Turner

paul waddle

>This is a little off the present subject,but Fred in your book MAKING SCREW THREADS IN WOOD,page 34,do you mean one should make the bored hole for the top threads,be .020 larger than d 1? .This for cleance to prevent jaming? If I read the formula correctly,subtracting d2 from d1,this makes the hole smaller. Its putting the minus sign in front of the expression that confuses this old mind. thks,pw

Re: Nova Ornamental Turner

#8

Nova Ornamental Turner-update

Bill McWhirter-

>Still have not been able to find out about the required "larger bed clamp plate (available as an accessory)" on the teknatool site. Talked with Tim Geist who knew nothing about it. He thought that I would have to get it fabricated by a machine shop. New Zealand number does not answer.

Has anyone ever used the Nova OT on a powermatic 3520 and if so, how did you attach it?

Re: Nova Ornamental Turner

#9

Re: Nova Ornamental Turner *LINK*

Fred Holder

>Hello Paul,

d-d1 should be a slip fit inside the internal threads. d-d2 would be slightly larger to allow for thread clearance. If they were exactly the same, the threads would not be able to screw together. I hope that explains it and is clear.


More Woodturning Website

Re: Nova Ornamental Turner

#10

Re: Nova Ornamental Turner-update

Dick Coers

>Bill, You are going to need a riser block/adapter. I bet you could make one out of hard maple and be off to the races. I looked at the manual on line and it shows two bolts holding the base to the lathe bed. You might have to cut some grooves in the top of your riser to adapt to the base, and you could put a strip of wood on your maple adapter to align it your machine. Then buy some longer bolts or all thread rod to bolt it to your lathe. Since these bolts put the hard maple in compression, I bet you wouldn't know the difference between the maple or steel.

Re: Nova Ornamental Turner

#11

Re: Nova Ornamental Turner

paul waddle

>Thks Fred,I sent you an email . I want to be sure I know what you are saying. And, If I make a lathe jig such as similar to the SG 400,the outcome depends on just touching the cutter on the shoulders.pw.