Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Sierra Button Click Pen help

Posts

Sierra Button Click Pen help

#1

Sierra Button Click Pen help

Jim Rutten

>Just turned my first one of these and I am having trouble getting it to click. First, there were a couple of small silver cylinders that were included with the kit but no clue of where they go since they were not included in the directions. Without them, the tip of the pen doesn't protrude and the button on top doesn't protrude. I finally figured out that the silver cylinder goes on top of the refill, but when I reassemble it both the tip of the pen and the button protrude. There doesn't seem to be a fudge factor in this pen (i.e. the center twist mechanism has to insert fully or there is a gap and the finial clip assembly have to go in fully or there is a gap).

I barrel trimmed the brass tube but just barely got any brass shavings. What am I missing? Any guesses?

Re: Sierra Button Click Pen help

#2

Re: Sierra Button Click Pen help

Marc Phillips

>The pen length is critical... sounds like you made it a little short. Just make the little silver refill extension a tad shorter... I just hold it in some padded vice grips and touch it to a disc sander... all the usual precautions apply, such as it getting hot etc... if you mar it up at all holding it, it wont click right.

Re: Sierra Button Click Pen help

#3

Re: Sierra Button Click Pen help

Jim Shaver - Oakville, Ont

>That small silver extension barrel is a new detail for me, it fits pressed into the end of the Parker cartridge and enables it to click, had the same issue myself. Works like a charm.

Take care,

Jim

Re: Sierra Button Click Pen help

#4

Re: Sierra Button Click Pen help

Jim Rutten

>Thanks Jim and Marc. I can't believe I am having this much trouble with this pen. I probably turned 50 of them (not this brand) when I first started turning. I decided to make some for my wife's fellow nurses. I will give what you mentioned a try.

Re: Sierra Button Click Pen help

#5

Re: Sierra Button Click Pen help

Jim Rutten

>Ok, now it is clicking but in order to "set" it when clicking the pen tip out and in order to reinsert it into the pen after clicking the pen tip in you have to push it in on a hard surface. Did I remove to much material off the silver cylinder? Not enough? Do you just have to "work them in"?

Re: Sierra Button Click Pen help

#6

Re: Sierra Button Click Pen help *LINK*

fredbear34

>The instructions for this pen that are available on Arizona Silhouette's web site give a very thorough explanation of these two chrome pieces (one is a spare), and that this extension was part of the design to allow flexibility in choosing what ink refill to use. There are also some great tips for avoiding critical errors in making this pen. The link is below. It is the availability of helps like this, as well as the great service and nice blanks, that makes AZ my supplier of choice. Hope this is of some help.


Sierra Button Click Pen Instructions

Re: Sierra Button Click Pen help

#7

Re: Sierra Button Click Pen help

Jim Rutten

>I now have three different sizes of silver cylinders. I have the one in it now that seems to leave the nicest amount of tip out. I am very happy with the turning portion of it. When I insert refill with the crome extension into the top portion while keeping pressure on the refill it seems to click with no hangups. When I put the spring and refill in the bottom portion it seems to work fine. When I assemble the whole pen I have bind issues (i.e. the pen tip goes out but does not retract into either the writing position nor the no tip position). What the heck is going on?

Re: Sierra Button Click Pen help

#8

Re: Sierra Button Click Pen help

GalenV in Iowa

>Unscrew the nib section a little at a time and each time try operating the pen. If it works you will find the body assembly too short. You can trim off the refill to account for shorter assembly by what you unscrewed the nib by.

Just a guess.

Re: Sierra Button Click Pen help

#9

Re: Sierra Button Click Pen help

Grant Wilkinson

>Jim: As has already been mentionned, the silver extension allows the pen to use either a Parker refill or a longer Uniball refill. If using a Parker style refill, you insert the extension into the end of the refill. One note, though, a genuine Parker refill does not have a hole in the end . Only after marker do. Some of us get around this by shortening the pen barrel to 1.90". The pen will then take a standard Parker refill without the extension. The downside is that it will not take the longer Uniball refill.