Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Perhaps OT Qs:Making a base

Posts

Perhaps OT Qs:Making a base

#1

Perhaps OT Qs:Making a base

Dinyar Chavda

>My wife wants me to make bases on which she can place her flower arrangement containers. I had a friend make slices from a black walnut tree, and so I have these discs with bark on them. I need to flatten each side, and make them parallel to each other. I don't have a planer, and I guess this is sort of like resawing on a bandsaw, except that I can't figure out how to hold the piece of wood so that it is safe, vertical, and the two sides end up being parallel. The bandsaw would normally twist the piece out of my hands (twisting the blade in the process), particularly when I start the cut, as the leading piece of the wood would not have any support under it (see picture below).

I thought of doing it on the lathe, but have concerns about how to hold it, and messing up the edges, as they are irregular.

Any suggestions would be appreciated.


img

Re: Perhaps OT Qs:Making a base

#2

Re: Perhaps OT Qs:Making a base

Gary Evans Tallassee, TN

>Hi Dinyar,

What are the dimensions of these pieces? I'm having difficulty picturing what you are dealing with. The words slices and discs and resawing leave me with a jumbled impression of what you need. If you are sawing the sides of a branch segment, I know a jig you can build to use on your bandsaw. If you are flattening the top and bottom of a disc, perhaps a support so that you can use a router for surfacing.

Gary

Re: Perhaps OT Qs:Making a base

#3

Re: Perhaps OT Qs:Making a base

Al Neighbors

>Dinyar, I suggest using double sided tape to hold the slice onto a faceplate. Flatten one side. Reverse, and flatten the other.

Good double sided tape will hold for this type of work.

Re: Perhaps OT Qs:Making a base

#4

Re: Perhaps OT Qs:Making a base

John Irvine

>if not bigger than the swing of your lathe just put them between centers and face off

Re: Perhaps OT Qs:Making a base

#5

Re: Perhaps OT Qs:Making a base

Mike Nelson

>I use Johns idea except I use a large chuck with a four prong morse spur just clearing the edge to keep it centered and an oval live center on the tail. Don't turn to fast, make light cuts then flip it over onto a vacumn chuck. I spray with laquer to fix the bark and make a seal for the vacumn chuck. Mike

Re: Perhaps OT Qs:Making a base

#6

Re: Answers to questions, and more questions

Dinyar Chavda

>I knew I wasn't doing a good job describing the issue, so, this time, I've included pictures of a couple of the rough discs.

Essentially, these were chainsawed in about 1" thicknesses, and they each include the pith of the tree. Gary, they are about 12" in diameter, although irregularly shaped (the more irregular, the more they are desired). They have the bark on, and that is also a plus. They are currently drying, and it's ok if they have cracks in them.

Al & John, these are basically oval or oblong shapes and also irregular--some very oblong. Given that, my question is whether you would still make the same suggestion.

Mike, I'm trying to picture your suggestion, and do you mean that the piece is sitting on the chuck, with the spur holding it in place? What's an oval live center?

TIA.

D


img

Re: Perhaps OT Qs:Making a base

#7

Re: Answers to questions, and more questions *LINK*

Fred Holder

>When faced with a problem such as this, I mount a disk of wood on a faceplate and mount it on the lathe spindle. I true this disk once on the lathe. I would then take a cardboard disk with a center mark on it and use it to approximately mark the enter the slabs. If there is enough swing on the lathe to handle the slab, mount it between the live tail center and the disk. True up the first side as close as you can to the live center. Repeat on the other side. You will then have to carve away the little part under the live center on each side.

You can sand the piece while it is mounted on the lathe and it should finish up pretty well.

If you don't want a mark on the face of the disk, insert a small piece of wood between the slab and the live tailcenter. I've trued up many pieces of wood in this manner.

Good Luck


More Woodturning Website

Re: Perhaps OT Qs:Making a base

#8

Re: Answers to questions, and more questions

bill Crommett

>From what I gather, you are trying to face off both side to make them flat and parallel.

I have done this with a belt sander and a Jack Plane. I like the suggestion of the double sided tape, and it has several applications depending on what shop equipment you have.

Re: Perhaps OT Qs:Making a base

#9

Re: Perhaps OT Qs:Making a base

Barry Irby

>I have a flat mdf disk mounted on a face plate and covered with neoprene. (Its a flat vacuum chuck.) I would press the pieces to it with the tail stock and face them off, turn them over and face them again. I made some small plastic disks out of High Density Polyethylene and drill a hole in them that fits on my live center. I put one of and use it as a pusher that will leave little or no mark. You could use a small disk of plywood or wood.

Another way is a Performax type drum sander. Pretty easy if you have the right equipment.

Re: Perhaps OT Qs:Making a base

#10

Re: Perhaps OT Qs:Making a base

Stuart Johnson

>If you want to use your band saw you could make a jig to hold the log secure. Then just run it through slicing off rounds sort of like slicing lunch meat in a deli.

Re: Perhaps OT Qs:Making a base

#11

making a flat surface

John K Jordan

>Another way to flatten any wooden surface, regardless of size or shape, is with a router. You have to build a simple jig but the idea is to make multiple overlapping passes by sliding the router back and forth on a frame over the work that is advanced down a pair of parallel rails. Some sanding is required.

This method is sometimes used to flatten a large slab or glueup for a table or workbench. I believe I saw photos and instructions on the flat forum here sometime back (check the archives) and also in an old FWW mag. This may preserve the bark more than some other methods.

JKJ

Re: Perhaps OT Qs:Making a base

#12

John is Right!

Jorge Castaneda~Downeast Maine

>The router with a proper jig and cutter is a sure and safe way of doing it.

You need to mountthe router on a sturdy flat "beam" that in turn slides on top of two parallel "dormers" I am giving them names hoping to convey meaning, the router has a bullnose bit installed and it's set to a light cut, the slab you are flattening must be immobilized somehow, carpet tape or similar will do, or hot melt glue.

Once you have that set up just scrub and scrub until you have a flat the dormers may need to be moved around to let you clean the whole surface, finish with sandpaper, flip the piece and repeat to flatten the other side.

$0.02

Jorge

Re: Perhaps OT Qs:Making a base

#13

Thanks to all

Dinyar Chavda

>Thank, everyone, for all your suggestions. I'll try doing these bases on the lathe. Plus I also have some to make that are too big for my lathe, and I'll look up the suggestion about the router-jig---I understand the basic concept behind it, but it would be nice to have more detailed information.

Once again, I thank you, and, soon, my wife will thank you also!

D

Re: Perhaps OT Qs:Making a base

#15

Re: Answers to questions, and more questions

Mike Nelson

>Dinyar, I put the four prong spur in my large jaw Nova chuck with the spur standing about 1/4 out from the face of the chuck then center the peice and bring up the tail stock with the center that has the removable point, I know it's removable because I haven't seen it in years, this leaves a sharp 'round' edged center, not oval, sorry, to hold the piece against the chuck. I tap the piece till it is against the outside edges of the chuck then turn the face flat, flip it over onto a vac chuck and do the other side. I bring the tail up for this too, then pull it away to remove the nub. I have been using this technique for a long time even on large chunks..just watch your speed.

Re: Perhaps OT Qs:Making a base

#16

Re: Perhaps OT Qs:Making a base

jim miles - Charlote NC

>Idea: Next time mount the length of wood ( 6 -12" maybe ) between centers. Turn several discs with space between them to sand etc. , on the lathe, Turn down the center "nub" as small as safe, cut apart, and finish off nub with orbital sander or by hand.