Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Have Laser? Use IT (dummy)!

Posts

Have Laser? Use IT (dummy)!

#1

Have Laser? Use IT (dummy)!

charlie belden

>Finally had some green wood big enough to use the MiniMonster on for a Mini lathe sized hollow form - in California Pepper. Had some pieces with pretty dark heartwood (or it could be spalting - though I don't know if pepper spalts).

Had to cut some of the HSS cutter off in order to get the "angled head"in the 1" opening. Had to borrow a neighbor's grinder, with a cut off disk to do it and on the way to returning the grinder remembered that I actually have one - and know where it is.

The MiniMonster was doing a great job - too great a job when I got a little carried away near the end of hollowing - WITHOUT THE LASER.

Now it's not like mounting the laser and setting it up is some kind of PITA - it isn't - at all. And once set up - it stays there - even if the ride gets a little bumpy.

In retrospect, I do recall thinking "I should probably put the laser on now that I'm getting close - but . . .".

Thankfully, I have a few more blanks of this stuff - and one's on the lathe now. Put the laser on - and found I'd left it on since playing with it - five months ago.

The neck on this thing was left thick so there'd be some meat for reverse chucking to work on the bottom. Once that had been done I'd planned on finishing the neck.

Better luck next time - with the laser of course.


img

Re: Have Laser? Use IT (dummy)!

#2

Re: Have Laser? Use IT (dummy)!

paul waddle

>I think you did very well,now is the time for a salvage. Turn a bowl to approximate the outside curve and the base being loacted where the hole will be. Apply epoxy and do again.pw

Re: Have Laser? Use IT (dummy)!

#3

Re: Have Laser? Use IT (dummy)!

charlie belden

>Paul:

Alas, the walls another inch or so up from the "turned through" are pretty thing. To get any meat at all to do an Add On repair would go almost up to the tangent point of the two major curves in the profile. That would interrupt the dark/light grain in the pepper too abruptly.

I just turned another similar piece in the same pepper - and once again - blew through the bottom - but in a much more easily fixed way.

Think I'll use a bland pepper blank for the next "learning experience" with the MiniMonster.

Turns out I've got a problem with the laser. Thought it was just dead batteries. It wasn't.

Looks like I need to call Monster and see about getting another laser. Wish they made a version that would run off 110V through a transformer.


img

Re: Have Laser? Use IT (dummy)!

#4

Laser source

Jim Pugh, Elyria, OH

>Charlie, this outfit used to have remote battery setups/12v dc connections for lasers. I just made a very quick check of their website but didn't see any. Perhaps you can spend more time or contact them. http://www.calpaclasers.com/

They do have a couple of push button on/off lasers that are mighty nice. Just a satisfied customer.

Re: Have Laser? Use IT (dummy)!

#5

Re: Have Laser? Use IT (dummy)!

paul waddle

>Sorry Charlie,this kinda shakes the confidence,but keep on keeping on. You WILL make a master piece. The prettiest woods don't always cooperate. Save the pcs for history. pw

Re: Have Laser? Use IT (dummy)!

#6

Dick Hines

Re: Have Laser? Use IT (dummy)!

Dick Hines

>Charlie, cutting through the wall of a hollow form with a laser really makes feel stupid. I know I have done it. I was haveing so much fun hollowing I forgot to change the setting on the laser when I got down to the bottom.

As my father used to say,"people who don't make mistakes ain't doing anything."

Re: Have Laser? Use IT (dummy)!

#7

Dennis in Southern Oregon

Re: Have Laser? Use IT (dummy)!

Dennis in Southern Oregon

>Charlie, have you checked your local office supply store for a replacement laser? My local Staples has half a dozen styles, one of which may fit or can be adapted to your system. I wouldn't worry about an AC unit unless your are doing production runs of hollow forms. I haven't changed the battery in mine since I set it up and probably have used it for tens or hours. Dennis

Re: Have Laser? Use IT (dummy)!

#8

Re: Have Laser? Use IT (dummy)!

charlie belden

>To clarify - I didn't blow through the bottom of these two while using the laser. The first blow through was without the laser "cause I know what I'm doing!" - which of course I didn't.

I WOULD have used the laser on the second one but, having forgotten to turn it off a week ago when I turned it on to see if it was still working, the batteries were dead. Got new ones AND a battery tester only to discover that it wasn't the batteries. It may be the switch or it may be the laser. The latter has a laser which fits in a hole in the support arm - which in turn has a very small hole in the bottom of the laser hole. A plastic tubing covers the wires from the laser to the battery pack with switch.

I've found that trying to jerry rig something up rather than just replacing the original part(s) causes me more grief than any money saved. So I'll order one from Monster and try not blowing through the bottom of any more pieces while waiting for it to arrive.

Re: Have Laser? Use IT (dummy)!

#9

Brad Vietje

Not Dummy -- just an educational moment ;~)

Brad Vietje

>Hey Charlie,

These are both common growing pains for hollow form turners getting used to new equipment and methods. You made some beautiful shapes out of very nice wood -- missed it by *that* much!

I generally don't use the laser at all for smaller pieces, but even on bigger pieces, I don't use the laser up near the top. If I can reach it and measure it with my fingers or a bent-wire caliper, then that's what I do.

Around the bottom, however, the laser measurement really does come in mighty handy, regardless of the size of the turning! The trick is to be sure you are always measuring perpendicular to the wood surface -- which means adjusting the setup very often when cutting around a tight curve.

You're extremely close to posting a spectacular piece -- I'll keep an eye out.

Safe spinning,

Brad Vietje

Newbury, VT