Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Bearing for a vac adaptor

Posts

Bearing for a vac adaptor

#1

Bearing for a vac adaptor

Carole Valentine

>I want to get rid of the HoldFast adaptor and make one like Jeff made, but he has a very slight leak in his bearing. Is there a specific type of bearing that should be used for vac applications that is truly sealed? If so, sources?

Re: Bearing for a vac adaptor

#2

Re: Bearing for a vac adaptor

Ralph

>I can't think of any, and my (work) bearing expert is at sea... But if his design is sucking air through the bearing, he is probably sucking the lube out of the bearing also. I would expect his bearing to suck dry at some point. It's probably not turning fast enough to overheat and lockup, but the metal and metal will not be good for the bearing.

Re: Bearing for a vac adaptor

#3

Re: Bearing for a vac adaptor

Barbara Gill, Remlik VA

>That is why my vacuum system didn't work with my old Nova until I bought the adapter from Packard. The Oneway is set up so it is not an issue.

Re: Bearing for a vac adaptor

#4

Re: Bearing for a vac adaptor

Carole Valentine

>Thanks Ralph. That's what I suspected...maybe that's why they have that diaphragm on the Holdfast? I don't want to take diaphragm off to look under it until it gets damaged and I have to replace it. The leak in Jeff's is very minor...he still draws plenty of vac.

Re: Bearing for a vac adaptor

#5

Re: Bearing for a vac adaptor

Carole Valentine

>Not sure what you are saying, Barb. I thought you used the HoldFast with your old Nova? Or was it the Oneway adapter? The HF works great with my DVR...pulls 28", but I hate fooling with the lamp rod.

Re: Bearing for a vac adaptor

#6

Re: Bearing for a vac adaptor

Don Orr

>I use a double sealed (not shielded) bearing I got from ENCO. Seems to work fine. I can pull over 20" with a 1.5fcm pump on solid wood, but not much on porous wood. Probably have leaks but don't care as long as it holds. The ones I have are the cheapos from India that are often on sale in their Hot Deals flyer for $2-3 each.

Re: Bearing for a vac adaptor

#7

Re: Bearing for a vac adaptor

Barbara Gill, Remlik VA

>The original set up used a bearing; it never would work because it was not air tight. I bought the adapter from Packard (thought it was called something else). The adepter made the system work fine. I was just giving another example of a bearing not being air tight.

Re: Bearing for a vac adaptor

#8

Re: Bearing for a vac adaptor

matt overton

>Carol,

I kept this link from an earlier post. I think this is what you are looking for.

http://www.inficonvacuumcomponents.com/en/vacuumballbearings.html

Re: Bearing for a vac adaptor

#9

Re: Bearing for a vac adaptor *LINK*

Dave Schell

>Here is the best article I have seen on making the various components of a vacuum system. He has a link to the double sealed bearings from McMaster-Carr. I bought the same ones and can pull 24hg from my homemade adapter.

http://carlford.info/assets/demos_classes/vaccum_chucks_demo/Vacuum_Chucks_Demo.pdf


Great article on Vacuum components

Re: Bearing for a vac adaptor

#10

Now I Remember

Barbara Gill, Remlik VA

>It has no bearing on anything except clarification. The adaptor I got was E-Z Vacuum Adaptor.

Re: Bearing for a vac adaptor

#11

Re: Now I Remember

david------WebKitFormBoundarylRgnhGioIdOlFg+1

>One of my first collaborations was with Barbara on the Nova 3000 vacuum bearing that did not work in the handwheel recess on the outboard side of the headstock. The EZ-vacuum bearing made Johnny Tolly's vacuum setup work like a charm. Switching the setup to the Vicmarc only involved shortening the thread length on the lamp rod. In my experience, what makes the vacuum effective or not is the density of the wood and the amount of voids/defects in the piece being reversed. Often coating the inside surface with Anchorseal helps--wait until it dries, of course. Haven't tried the Oneway vacuum bearing.

Re: Bearing for a vac adaptor

#12

Re: Bearing for a vac adaptor

Ken

>QUESTION,I just bought the holdfast and was told that it would fit on my Nova 1624 without having to purchase any adapt.Is this true?My Nova is at my place in NC and so I havn't had a chance to try it out,but if I will need an adapt,I would like to get it before I head north.Any help would be appreciated.

Ken

Re: Bearing for a vac adaptor

#13

Mike Peace

Re: Bearing for a vac adaptor

Mike Peace

>I built my rotary bearing adapter for my PM3520 with a pump bearing from Lowes, part 99502-H .625 Bore, double sealed for Ace Pump found in Drawer K10, Specialty Fasteners. Cost was $7.10. Be sure to get a double sealed and not a shielded bearing or the vacuum pump will suck out all the grease.

Re: Bearing for a vac adaptor

#14

Keith Tompkins

Re: Bearing for a vac adaptor

Keith Tompkins

>Caorle, You want double sealed NOT double shielded bearings. I use two bearings with a spacer in between them. The tube or threaded rod that passes through the bearings must be sealed to prevent leaks JB weld works well. I also make a groove for a rubber o-ring between my adapter and the wood block that holds the bearings to reduce vacuum leaks.

Re: Bearing for a vac adaptor

#15

Re: Bearing for a vac adaptor

Carole Valentine

>Ken, it should work fine. It works fine on my DVR. I just decided I wanted to get rid of the lamp rod, so I am turning an adapter out of cherry to fit into the recesss of my handwheel like the one Jeff made for his Jet Mini. It is turned so that it fits super snug with one wrap of neoprene (Foamie)into the Nova handwheel. It will be drilled and fitted with a bearing, then the rest of the hardware will be added. All I will have to do is grab it and pull it out instead of fiddling with unscrewing the inboard nut on the lamp wheel. Jeff just sent me a sketch since I am vacuum system /fittings challenged (read "idiot"). LOL Maybe he will pipe up and post it so ya'll can see too.

Re: Bearing for a vac adaptor

#16

lamp "rod"..where's that darn edit button!

Carole Valentine

>

Re: Bearing for a vac adaptor

#17

Re: Bearing for a vac adaptor

mfoster

>Well this is a timely topic for me. I've been reworking my rotary adapter. I used to pull about 20 in of hg with an older adapter that I made which finally failed (rubber seals failed). I have tried to duplicate my previous efforts with several bearings, but none have been able to get more than 10 in of hg for me. It has been rather frustrating. I have absolutely isolated the vacuum leak to the bearings. My most recent thoughts for fixing the leaks was to find a really thick grease but now i think I may give another go at two double sealed bearings. My latest iteration was to use the double shielded bearings, which leaked like a sieve (3 in of hg). I was thinking they may last longer than the rubber seals, bad idea.

I use a design someone came up with (not me but I can't remember who) that allows you to keep the adapter on the handwheel. Just remove the vacuum hose and I can use a knock out bar to remove MT drives. If I get a decent vacuum running, I'll post pics of my version.

Mike

Re: Bearing for a vac adaptor

#18

Re: Bearing for a vac adaptor

Carole Valentine

>Mike, that's what I would like to figure out, but I can't think for the life of me how you can leave it on and still use a knockout bar. When you get it done let us know how! Probably won't work for me since the Nova DVR is rather weird - the hand wheel is male and threads into the spindle rather than the other way around.

Re: Bearing for a vac adaptor

#19

Re: Bearing for a vac adaptor

Ed in Leaside

>I didn't have any sealed bearing on hand when I built my vac chuck. The temporary fix was a rubber disk, cut from a dead bicycle tube, stuck to the bearing with some grease. It's been in use since Oct '07 and the centre hole, which rubs on the brass tube, is finally wearing out.

Re: Bearing for a vac adaptor

#20

Re: Bearing for a vac adaptor

Jeff Willaford

>I built a variation of Carl Ford's EZ Adapter style without the lamp rod. Press fit into the hand wheel. I used the double shielded bearing Carl called out. I drop about 2 inches of vacuum thru the bearing but still have 23-24 inches thru the spindle. I would think this is plenty from what I've read.

Re: Bearing for a vac adaptor

#21

That "really thick grease" is called vacuum grease

Al Crandall

>I use two bearings in my design, and leave room between them for vacuum grease. No need to reinvent the wheel, the item you want is already in existance.

Re: Bearing for a vac adaptor

#22

Re: That "really thick grease" is called vacuum gr

Russ Fairfield

>And a handy place to buy it is at a pool supply shop, if you live where they have such things.