Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Foot Switch

Posts

Foot Switch

#1

Foot Switch

Jerry Whitaker

>Can someone explain to me how to wire up a foot switch? I tried every combination of wiring I could think of and every time, it blew the cirtuit breaker. The switch has three terminals and a ground. I bought a 10 ft. extension cord and cut the female end off to a foot long. The rest of it (the male end) is the one that goes to the wall plug. I hooked up both of the green wires to the green ground terminal. There are 3 other terminals....NC (normally closed) NO )normaly open) and C (i assume is common). So, basically, I need to know where the black and white wires go. If someone could tell me where the black & white wires on the male end go and where the black and white wires on the female end go, I think I could take it from there.

Re: Foot Switch

#2

Rob Wallace

Re: Foot Switch

Rob Wallace

>Jerry:

In short, switches always are wired into the black ("hot") side of the circuit. The wires on return (white, or "cold") side are almost always wired together, as are the ground (bare or green) wires. The make and break sides of the switch are wired into the circuit to simply open and close the black "black wire" side of the circuit. Without seeing the circuit itself, and the "plugs" you are attempting to use, it is hard to tell you exactly what wire to put where, other than to tell you that white wires go with white wires, green/bare with green/bare, and switches are placed into the 'black' part of the circuit.

Trying 'all possible combinations' of the wires is a recipe for disaster (...or at least an extreme exercise for your circuit breaker panel or local fire department), and I would advise that you get in contact with someone with experience doing electrical wiring to at least check your wiring work before energizing the circuit. Doing most wiring is somewhat simple if you have experience, but can be extremely complicated and dangerous if you don't.

It's your decision as to what amount of risk you are willing to take...

Rob Wallace

Re: Foot Switch

#3

Rob Wallace

Forgot to mention that.....

Rob Wallace

>......the black wires should be the ones used to connect to the normally open (NO) terminals. When the foot switch is de-activated (i.e. not pushed 'ON') the NC terminals have a short between them, and the NO terminals are 'open'. Activating the switch (pressing the foot pedal) closes the NO terminals and this should give you the continuity in the black side of the circuit to turn on the current.

(If the switch has a schematic diagram and terminal layout, this should become obvious as to what is happening.)

White wires should be tied together, as should green/bare wires.

Good Luck,

Rob

Re: Foot Switch

#4

Re: Foot Switch

Chuck Engstrom

>Hi Jerry -- Bear in mind that you need to put your single-pole switch into only one side of the circuit, which should be the black wire. The green ground wire and the white wire should go straight on through and are not involved with the switch itself. (If you are doing this for 220-volts you probably ought to look for a double-pole switch.)

So you would bring the male wall-plug side of the black wire to the C (common) terminal and attach the female socket side of the black wire to the NO (normally open) side of the foot switch. When you press with your foot, the switch will close the path between the C and the NO and allow current to flow through to your socket end where it will start your motor or light or other load.

In practice this typically means that you are going to have your wire coming into AND going out of the foot switch you have wired yourself. You can even do it by just cutting off the outer jacket and breaking only the black lead to go to the switch mechanism, leaving the ground and white wires to pass through uncut. But it will still look like there are two wires attached to the foot switch.

Store-bought foot switches often incorporate specially constructed plug and socket sets which use only a single wire into the switch, with both plug and socket molded into a single piece that plugs into the wall receptacle, as in the photo. And others incorporate speed control circuits for motors, as for sewing machines or Foredom carving tools.

By all means wait a bit here and let someone else pitch in to review my suggestions and correct them if needed.

Best--

Chuck


img

Re: Foot Switch

#5

Re: Foot Switch

arkie

>Assuming you're talking 120V power:

You're almost there. Leave both green wires connected to the green screw. Connect both white wires together. They are not connected to the switch. Wire one black wire to the "C" terminal and the other to the "NO" terminal.

Connect a lamp to test. Make sure the lamp turns on and off when you step on the switch. If it works backward, move the black wire from "NO" to "NC" and be thankful you tested with a lamp. :)

Should be good tto go by now if the switch is rated to handle the current you're switching.

Re: Foot Switch

#6

do they make 220 volt foot switches????

Adrien

>

Re: Foot Switch

#7

Re: do they make 220 volt foot switches????

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Yes, You can even use it on 3 phase, and with VFD controls. I have one on two of my lathes.

On the Powermatic 45, I use a momentary contact. I have to hold my foot on it to run the motor. I eliminated the start stop buttons. It is simply wired between L 3 and the coil. Of course the line out of the coil goes through the heaters which protect the motor.

On my big lathe, I used a toggle type, wired into the VFD. One tap of the switch turns it on, and the next turns it off.

Both have the shroud to protect against accidental starts, but beware, it is still very easy to get on them by accident.

Re: Foot Switch

#8

Yes, and they use switches outside their ratings.

arkie

>

Re: Foot Switch

#9

Re: Foot Switch

Jerry Whitaker

>Thanks, everyone. I am sure you are all right about your suggestions but the explanation from Arkie was the simplest for me to understand and guess what....it worked. I knew someone on WC other than a high priced electrician could help me. Jerry

Re: Foot Switch

#10

If you really want meaningful advice,

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Go back to the beginning and study your beginning question. You didn't tell anyone what lathe you have. You make no mention of what type of switch starts and stops your motor now. No model number, starter, or motor.

Nobody reading this forum wants to read your obit, and feel responsible for it. It would take a full book to cover all of the possible option for all lathes that are out there. Those books already exist if you want to go that route.

But please realize, that when you ask such vague questions it requires those willing to give advice to give longer answers when they don't know the givens to your specific question.

Please don't think I am jumping on you. I am only offering you advice as to how to frame your questions in the future. While you walk into your shop, you can see your lathe. BUT we on this side of the computer screen have no idea what you need, unless you are willing to help clear the fog. Do you catch my drift?

Re: Foot Switch

#11

Re: If you really want meaningful advice,

Jerry Whitaker

>I appreciate your concern Keith.....I just wanted to wire the switch so I could operate a dremel tool. Don't think I would ever want a footswitch hooked up to my lathe or any large piece of machinery.

Re: Foot Switch

#12

Re: If you really want meaningful advice,

Bill Howatt

>That makes a big difference since this forum tends to deal primarily with lathe issues by default.

Green-Green

White-White

Black from male plug on cord to C

Black to female receptacle on cord to NO

(If you put the black wire on NC, then the dremel will run until you press the switch, and you don't want that.)

Be sure you carefully connect the wires and use proper wire nuts to reconnect any wires you have cut such as the white and possibly the green. If you have a ground screw you may find it better to put a short piece of #14 wire (a pigtail) under the ground screw if there is one and then connect the two greens from the cut cord to it and bond them with a wire nut. The alternative is to twist the 2 greens together and put under the screw but sometimes this makes too big of a wire for good mounting under the screw.

As always, when dealing with a 120V circuit you want to put the switch in the hot lead which is the black.

The green safetly ground must never be switched and must always be connected together and to the ground terminal of any piece of equipment having a ground terminal. Total plastic "devices" may or may not have a ground connection but a metal one almost always will.

The neutral (white wire) is usually not switched.

I only use a foot switch on my drill press where I find it very convenient because it frees up a hand and I could see this benefit in using a dremel. I personally feel that they reduce the level of safety and would not use them on any other device because I don't see any real benefit. Be careful.

Bill

Re: Foot Switch

#13

Re: If you really want meaningful advice,

Jerry Whitaker

>Thanks for your input, Bill