Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Not Chattering

Posts

Not Chattering

#1

Not Chattering

Ron McKinley

>When Gil Jones posted a photo of his home made chatter tool I remembered that I bought a Crown version several years ago and had never used it. So, I looked around and finally found it and tried it on the tops of some bottle stoppers today without much success. I followed the directions�1,000 to 3,000 rpm, 1 1/2" to 2" overhang, tool rest a little high with the cutter slanted down.

I tried it on cocobolo, zebrawood, all rather dense exotics. I put a bur on the cutter and tried it center outward and rim inward. Hardly anything. I tried light pressure and heavier pressure and still nothing much. Is this one of those tools where someone has to give you the secret handshake? Not chattering in Apple Valley...Ron

Re: Not Chattering

#2

Re: Not Chattering

john lucas

>I use it at slower speeds. Try tilting it to the left and cutting at about the 7 oclock position. You may have to push fairly hard depending on the wood. Once it starts to chatter and squeel pull it across the wood. I put a blank in the lathe and try it varying the pressure and speed of the lathe. If it doesn't work right I face off the wood and try again. When I get it right I cut this button off and make another. After a few minutes you'll have 5 to 10 little chatter buttons that can be inserted in other projects.

You didn't mention whether you were using the wood side grain or end grain. Side grain won't chatter, it just tears up the wood. The chatter tool only works on endgrain. Cocobolo is an excellent wood for this. it is a more subtle chatter. On a wood like maple you will have to push harder but it will give you a deeper chatter.

Once you've learned to get it to chatter you can try tilting to the right for a different look. Leaving it in one direction leaves a sort of spiral. by tilting it left, then right, you get a sort of herringbone look.

Re: Not Chattering

#3

Re: Not Chattering

Ron McKinley

>Thanks John. I was using it on endgrain. Bonnie Klein makes it look so easy in her video. I'll slow it down to about 500 rpm and try some more.......Ron

Re: Not Chattering

#4

Re: Not Chattering

john lucas

>Ron I remember having trouble when I was learning. I think you just sort of find the right touch for your particular tool and then after than it comes more easily. If you ever get to see Michael Mocho, he is a wizard with the chatter tool. You might also vary the length the tool is suspended from the main tool body. That along with how much of the overall tool hangs over the tool rest seems to be what gives the best chatter.

Re: Not Chattering

#5

Re: Not Chattering

robo hippy

>I like the higher speeds for the chatter tool. Have the tip at a 45 degree angle or more pointing down. The pressure can be meduim or light, and will give different results. Get a block of hard maple, and make a bunch of practice attempts, cutting off the pattern with a spindle gouge after each attempt. I take one with me, specifically for that purpose when doing demo/workshops. Also, you don't want a burr on it as the burr will cut/tear the wood fibers, and a polished, honed edge will dent it.

robo hippy

Re: Not Chattering

#6

Brad Vietje

Re: Not Chattering

Brad Vietje

>Ron,

Try extending the tip for maximum chatter, and don't support or touch the tip -- just the shaft. You want the toolrest back rather far so the vibrating tip is free to wiggle.

Have fun,

Brad Vietje

Newbury, VT

Re: Not Chattering

#7

Re: Not Chattering

Ron McKinley

>I was wondering about that. The instructions said sharpen and raise a burr but I remember Bonnie Klein saying she seldom, if ever, sharpens hers. I'll keep trying all the suggestions until I find one that works....Thanks........Ron